Regulation No. 107-04

Name:Regulation No. 107-04
Description:General Construction of M2 or M3 Vehicles
Official Title:Uniform Provisions Concerning the Approval of: Category M2 or M3 Vehicles with Regard to their General Construction.
Country:ECE - United Nations
Date of Issue:2011-12-12
Amendment Level:04 Series, Corrigendum 1, Revision 4
Number of Pages:136
Vehicle Types:Bus
Subject Categories:Prior Versions
Available on InterRegs.NET

Our online subscription service, offering immediate access to our extensive library of global vehicle regulations, standards and legislation. A fully searchable, accurate, user-friendly resource for consolidated regulations that are updated quickly and frequently.

Tell me more | Already a subscriber

Available on SelectRegs.com

Our fast and easy means of purchasing up-to-date global vehicle and component standards and regulations on a pay-as-you-go basis. Pay securely by credit card and your documents are delivered directly and immediately to your computer as PDF files.

Tell me more | Go straight to site

Keywords:

vehicle, door, paragraph, annex, case, vehicles, wheelchair, seat, passengers, driver, space, regulation, class, service, approval, device, requirements, position, mass, means, figure, emergency, provided, area, type, fitted, height, seats, deck, floor, doors, force, series, amendments, number, maximum, plane, passenger, technical, bodywork, compartment, access, minimum, test, step, system, vertical, front, part, width

Text Extract:

All InterRegs documents are formatted as PDF files and contain the full text, tables, diagrams and illustrations of the original as issued by the national government authority. We do not re-word, summarise, cut or interpret the regulatory documents. They are consolidated, published in English, and updated on a regular basis. The following text extract indicates the scope of the document, but does not represent the actual PDF content.

E/ECE/324
) Rev 2/Add.106/Rev.4/Corr.1
E/ECE/TRANS/505 )
December 8, 2014
STATUS OF UNITED NATIONS REGULATION
ECE 107-04
UNIFORM PROVISIONS CONCERNING THE APPROVAL OF:
CATEGORY M OR M VEHICLES WITH
REGARD TO THEIR GENERAL CONSTRUCTION
Incorporating:
00 series of amendments
Date of Entry into Force: 18.06.98
Corr. 1 to the 00 series of amendments
Dated: 12.11.98
Supplement 1 to the 00 series of amendments
Date of Entry into Force: 21.02.02
Supplement 2 to the 00 series of amendments
Date of Entry into Force: 11.08.02
Supplement 3 to the 00 series of amendments
Date of Entry into Force: 10.12.02
Corr. 1 to Supplement 3 to the 00 series of amendments
Dated: 13.11.02
Supplement 4 to the 00 series of amendments
Date of Entry into Force: 30.10.03
01 series of amendments
Date of Entry into Force: 12.08.04
02 series of amendments
Date of Entry into Force: 10.11.07
Supplement 1 to the 02 series of amendments
Date of Entry into Force: 11.07.08
Supplement 2 to the 02 series of amendments
Date of Entry into Force: 15.10.08
Corr. 1 to Revision 2 to the 02 series of amendments
Dated: 03.03.10
Corr. 2 to Revision 2 to the 02 series of amendments
Dated: 16.06.10
Supplement 3 to the 02 series of amendments
Date of Entry into Force: 22.07.09
Supplement 4 to the 02 series of amendments
Date of Entry into Force: 24.10.09
Supplement 5 to the 02 series of amendments
Date of Entry into Force: 24.10.09
Corr. 1 to Supplement 5 to the 02 series of amendments
Dated: 28.04.11
Supplement 6 to the 02 series of amendments
Date of Entry into Force: 09.12.10
Supplement 7 to the 02 series of amendments
Date of Entry into Force: 23.06.11
Corr. 1 to Revision 3 of the Regulation
Dated: 14.03.12
03 series of amendments
Date of Entry into Force: 19.08.10
Supplement 1 to the 03 series of amendments
Date of Entry into Force: 09.12.10
Supplement 2 to the 03 series of amendments
Date of Entry into Force: 28.10.11
04 series of amendments
Date of Entry into Force: 28.10.11
Supplement 1 to the 04 series of amendments
Date of Entry into Force: 26.07.12
Supplement 2 to the 04 series of amendments
Date of Entry into Force: 18.11.12
Supplement 3 to the 04 series of amendments
Date of Entry into Force: 10.06.14
Corr. 1 to Revision 4 of the Regulation
Dated: 08.12.2014
Supplement 4 to the 04 series of amendments
Date of Entry into Force: 09.10.14

Regulation No. 107
UNIFORM PROVISIONS CONCERNING THE APPROVAL OF CATEGORY M OR M
VEHICLES WITH REGARD TO THEIR GENERAL CONSTRUCTION
CONTENTS
REGULATION
1. Scope
2. Definitions
3. Application for approval
4. Approval
5. Requirements
6. Modification and extension of approval of a vehicle type or bodywork type
7. Conformity of production
8. Penalties for non-conformity of production
9. Production definitively discontinued
10. Transitional provisions
11. Names and addresses of Technical Services responsible for conducting approval tests, and of
Type Approval Authorities
12. (Reserved)

Annex 11 - Masses and dimensions
Annex 12 - Additional safety prescriptions for trolleybuses

2.1.1.4. A vehicle may be regarded as belonging in more than one Class. In such a case it may be
approved for each Class to which it corresponds.
2.1.2. For vehicles having a capacity not exceeding 22 passengers in addition to the driver, there
are two classes of vehicles:
2.1.2.1. "Class A" Vehicles designed to carry standing passengers; a vehicle of this class has seats
and shall have provision for standing passengers.
2.1.2.2. "Class B" Vehicles not designed to carry standing passengers; a vehicle of this class has
no provision for standing passengers.
2.1.3. "Articulated vehicle" means a vehicle which consists of two or more rigid sections which
articulate relative to one another; the passenger compartments of each section
intercommunicate so that passengers can move freely between them; the rigid sections are
permanently connected so that they can only be separated by an operation involving
facilities which are normally only found in a workshop.
2.1.3.1. "Double-decker articulated vehicle" means a vehicle which consists of two or more rigid
sections which articulate relative to one another; the passenger compartments of each
section intercommunicate on at least one deck so that passengers can move freely between
them; the rigid sections are permanently connected so that they can only be separated by
an operation involving facilities which are normally only found in a workshop.
2.1.4. "Low floor vehicle" is a vehicle of Class I, II or A in which at least 35% of the area
available for standing passengers (or in its forward section in the case of articulated
vehicles, or in its lower deck in the case of double-decker vehicles) forms an area without
steps and includes access to at least one service door.
2.1.5. "Bodywork" means a separate technical unit comprising all the special internal and
external equipment of the vehicle.
2.1.6. "Double deck vehicle" means a vehicle where the provided spaces for passengers are
arranged, at least in one part, in two superimposed levels and spaces for standing
passengers are not provided in the upper deck.
2.1.7. "Separate technical unit" means a device intended to be part of a vehicle, which may be
type-approved separately, but only in relation to one or more specified types of vehicle.
2.1.8. "Trolleybus" means a vehicle, electrically driven by energy from external, overhead contact
wires. For the purposes of this Regulation, it also includes such vehicles having an
additional internal means of propulsion (dual mode vehicles) or having a means of
temporary external guidance (guided trolleybuses).
2.1.9. "Vehicle without roof" means a vehicle without roof over all or part of its deck. In the
case of a double-decked vehicle this shall be the upper deck. Space for standing
passengers shall not be provided on any deck without roof, independently of the class of
vehicle.

2.11. "Escape hatch" means an opening in the roof or the floor intended for use as an
emergency exit by passengers in an emergency only.
2.12. "Emergency exit" means an emergency door, emergency window or escape hatch.
2.13. "Exit" means a service door, intercommunication staircase, half-staircase or emergency
exit.
2.14. "Floor or deck"
2.14.1. "Floor" means that part of the bodywork whose upper surface supports standing
passengers, the feet of seated passengers and the driver and any crew member, and may
support the seat mountings;
2.14.2. "Deck" means that part of the floor provided only for the passengers.
2.15. "Gangway" means the space providing access by passengers from any seat or row of
seats or each special area for wheelchair users to any other seat or row of seats or each
special area for wheelchair users or to any access passage from or to any service door or
intercommunication staircase and any area for standing passengers; it does not include:
2.15.1. The space extending 300mm in front of any seat, except where a sideways-facing seat is
situated above a wheel arch, in which case this dimension may be reduced to 225mm
(see Annex 4, Figure 25);
2.15.2. The space above the surface of any step or staircase (except where the surface of the step
is contiguous with that of a gangway or access passageway); or
2.15.3. Any space which affords access solely to one seat or row of seats or a facing pair of
transverse seats or row of seats.
2.16. "Access passage" means the space extending inwards into the vehicle from the service
door up to the outermost edge of the upper step (edge of the gangway), intercommunication
staircase or half-staircase. Where there is no step at the door, the space to be considered
as access passage shall be that which is measured according to Annex 3, Paragraph 7.7.1.
up to a distance of 300mm from the starting position of the inner face of the test gauge.
2.17. "Driver’s compartment" means the space intended for driver’s exclusive use except in the
case of an emergency and containing the driver’s seat, the steering wheel, controls,
instruments and other devices necessary for driving or operating the vehicle.
2.18. "Mass of the vehicle in running order" means the mass of the unladen vehicle with
bodywork, and with coupling device in the case of a towing vehicle, in running order, or the
mass of the chassis with cab if the manufacturer does not fit the bodywork and/or coupling
device (including coolant, oils, 90% fuel, 100% other liquids except used waters, tools,
spare wheel and driver (75kg), and, for buses and coaches, the mass of the crew member
(75kg) if there is a crew seat in the vehicle.
2.19. "Technically permissible maximum laden mass (M)" means the maximum mass of the
vehicle based on its construction and performance, stated by the manufacturer. The
technically permissible maximum laden mass is used to determine the vehicle category.
2.20. "Passenger" means a person, other than the driver or a member of the crew.

2.36. "Front" and "Rear" means the front or rear of the vehicle according to the normal direction
of travel and the terms; "forward", "foremost", "rearward" and "rearmost" etc. shall be
construed accordingly.
2.37. "Intercommunication staircase" means a staircase which allows communication between
the upper and lower decks.
2.38. "Separate compartment" means a space in the vehicle which may be occupied by
passengers or crew when the vehicle is in use and which is separated from any other
passenger or crew space, except where any partition allows passengers to see into the next
passenger space, and is connected by a gangway without doors.
2.39. "Half-staircase" is a staircase from the upper deck which terminates in an emergency door.
2.40. "Service-door lighting" means a lighting device(s) of the vehicle designed to illuminate the
exterior vicinity of service doors and wheels.
3. APPLICATION FOR APPROVAL
3.1. The application for approval of:
a) A vehicle type or;
b) A separate technical unit type or;
c) A vehicle type fitted with bodywork type already approved as a separate technical unit
With regard to its constructional features shall be submitted by the responsible manufacturer
or by his duly accredited representative.
3.2. In the case of an application for approval of a vehicle made by assembling a chassis with
type-approved bodywork, the term manufacturer refers to the assembler.
3.3. A model for the information document relating to the constructional features is given in
Annex 1 - Part 1.
3.3.1. Appendix 1: for a vehicle type,
3.3.2. Appendix 2: for a bodywork type.
3.3.3. Appendix 3: for a vehicle type fitted with bodywork already approved as a separate technical
unit.
3.4. A vehicle(s) or a bodywork(s) representative of the type to be approved shall be submitted
to the Technical Service responsible for conducting the type-approval tests.
4. APPROVAL
4.1. If the vehicle or bodywork submitted for approval pursuant to this Regulation meets the
requirements of Paragraph 5, below approval of that vehicle or bodywork type shall be
granted.

5.3. Contracting Parties shall be free to choose the most appropriate solution to achieve
improved accessibility in vehicles other than those of Class I. However, if vehicles other
than those of Class I are equipped with features or devices for people with reduced mobility
and/or wheelchair users, those features or devices shall comply with the relevant
requirements of Annex 8.
5.4. Nothing in this Regulation shall prevent the national authorities of a Contracting Party from
specifying that certain types of operation are reserved for vehicles which are equipped for
the transport of passengers with reduced mobility in accordance with Annex 8.
5.5. Unless otherwise stated, all measurements shall be made when the vehicle is at its mass in
running order and it is standing on a smooth and horizontal ground surface and in the
normal condition for travel. If a kneeling system is fitted, it shall be set so the vehicle is at its
normal ride height for travel. In the case of approval of bodywork as a separate technical
unit the position of the body relative to the flat horizontal surface shall be specified by the
manufacturer.
5.6. Wherever there is a requirement in this Regulation for a surface in the vehicle to be
horizontal or at a specific angle when the vehicle is at its mass in running order, in the case
of a vehicle with mechanical suspension, the surface may exceed this slope or possess a
slope when the vehicle is at its mass in running order, provided that this requirement is met
when the vehicle is in the loading condition declared by the manufacturer. If a kneeling
system is fitted to the vehicle, it shall not be in operation.
6. MODIFICATION AND EXTENSION OF APPROVAL OF A VEHICLE OR BODYWORK
TYPE
6.1. Every modification of the vehicle or bodywork type shall be notified to the Type Approval
Authority which approved the vehicle type. That Authority may then either:
6.1.1. Consider that the modifications made are unlikely to have an appreciable adverse effect and
that, in any case, the vehicle or bodywork still complies with the requirements; or
6.1.2. Require a further test report from the Technical Service responsible for conducting the tests.
6.2. Confirmation or refusal of approval, specifying the modifications, shall be communicated by
the procedure specified in Paragraph 4.3. of this Regulation to the Contracting Parties to the
Agreement which apply this Regulation.
6.3. The Type Approval Authority issuing the extension of approval shall assign a series number
for such an extension and inform thereof the other Contracting Parties to the 1958
Agreement applying this Regulation by means of a communication form conforming to the
model in Annex 1, Appendix 2 to this Regulation.
7. CONFORMITY OF PRODUCTION
The conformity of production procedures shall comply with those set out in the Agreement,
Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev. 2), with the following requirements:
7.1. Vehicles and bodyworks approved to this Regulation shall be so manufactured as to
conform to the type approved by meeting the requirements set forth in Paragraph 5 above.

10.8. As from 24 months after the date of entry into force of Supplement 5 to the 02 series of
amendments, Contracting Parties applying this Regulation may refuse first national
registration (first entry into service) of a vehicle which does not meet the requirements of
Supplement 5 to the 02 series of amendments to this Regulation.
10.9. As from the official date of entry into force of the 03 series of amendments, no Contracting
Party applying this Regulation shall refuse to grant approval under this Regulation as
amended by the 03 series of amendments.
10.10. No Contracting Party applying this Regulation shall refuse national or regional type approval
of a vehicle type approved to the 03 series of amendments to this Regulation.
10.11. As from December 31, 2012, Contracting Parties applying this Regulation shall grant
approvals only if the vehicle type to be approved meets the requirements of this Regulation
as amended by the 03 series of amendments.
10.12. As from December 31, 2013, Contracting Parties applying this Regulation may refuse to
grant national or regional approvals and may refuse first national or regional registration
(first entry into service) of a vehicle which does not meet the requirements of the 03 series
of amendments to this Regulation.
10.13. As from the official date of entry into force of the Supplement 6 to the 02 series of
amendments, no Contracting Party applying this Regulation shall refuse to grant approval
under this Regulation as amended by the Supplement 6 to the 02 series of amendments.
10.14. As from 12 months after the date of entry into force of the Supplement 6 to the 02 series of
amendments, Contracting Parties applying this Regulation shall grant approvals only if the
vehicle type to be approved meets the requirements of this Regulation as amended by
Supplement 6 to the 02 series of amendments.
10.15. As from 30 months after the entry into force of Supplement 6 to the 02 series of
amendments, Contracting Parties applying this Regulation may refuse to grant
national/regional approvals and first national registration (first entry into service) of a vehicle
which does not meet the requirements of Supplement 6 to the 02 series of amendments to
this Regulation.
10.16. As from the official date of entry into force of the 04 series of amendments, no Contracting
Party applying this Regulation shall refuse to grant approval under this Regulation as
amended by the 04 series of amendments.
10.17. As from 24 months after the date of entry into force of the 04 series of amendments,
Contracting Parties applying this Regulation shall grant approvals only if the vehicle type to
be approved meets the requirements of this Regulation as amended by of the 04 series of
amendments.
10.18. As from 36 months after the entry into force of the 04 series of amendments, Contracting
Parties applying this Regulation may refuse to grant national/regional approvals and first
national registration (first entry into service) of a vehicle which does not meet the
requirements of the 04 series of amendments to this Regulation.
10.19. Contracting Parties applying this Regulation shall not refuse to grant extensions of approval
to the 03 series of amendments to this Regulation for vehicles which are not affected by the
04 series of amendments.

ANNEX 1
APPROVAL DOCUMENTATION
PART 1
APPENDIX 1
MODEL INFORMATION DOCUMENTS
Model information document pursuant to Regulation No. 107 relating to type-approval of
Category M or M vehicles with regard to their general construction
The following information, if applicable, shall be supplied in triplicate and include a list of contents. Any
drawings shall be supplied in appropriate scale and in sufficient detail on size A4 or on a folder of A4
format. Photographs, if any, shall show sufficient detail.
If the systems, components or separate technical units have electronic controls, information concerning
their performance shall be supplied.
1.
GENERAL
1.1.
Make (trade name of manufacturer): ........................................................................................
1.2.
Type: .........................................................................................................................................
1.2.1.
Chassis: ....................................................................................................................................
1.2.2.
Bodywork/complete vehicle: .....................................................................................................
1.3.
Means of identification of type, if marked on the vehicle
: ......................................................
1.3.1.
Chassis: ....................................................................................................................................
1.3.2.
Bodywork/complete vehicle: .....................................................................................................
1.3.3.
Location of that marking: ...........................................................................................................
1.3.3.1.
Chassis: ....................................................................................................................................
1.3.3.2.
Bodywork/complete vehicle: .....................................................................................................
1.4.
Category of vehicle
: ...............................................................................................................
1.5.
Name and address of manufacturer: ........................................................................................
1.6.
Address(es) of assembly plant(s): ............................................................................................

3.4. Mass of the vehicle with bodywork, and in the case of a towing vehicle of a category other
than M , with coupling device, if fitted by the manufacturer, in running order, or the mass of
the chassis or chassis with cab, without bodywork and/or coupling device if the
manufacturer does not fit the bodywork and/or coupling device (including liquids, tools,
spare wheel and driver, and, for buses and coaches, a crew member if there is a crew seat
in the vehicle) (maximum and minimum for each variant):
3.4.1. Distribution of this mass among the axles and, in the case of a semi-trailer or centre axle
trailer, load on the coupling point (maximum and minimum for each variant):
3.5.
Technically permissible maximum laden mass stated by the manufacturer
(maximum and
minimum for each variant):
3.5.1. Distribution of this mass among the axles (maximum and minimum for each variant):
3.6. Technically permissible maximum laden load/mass on each axle:
3.7. Technically permissible maximum mass on the coupling point:
3.7.1. Of the motor vehicle:
4. BODYWORK
4.1. Type of bodywork: single deck/ double deck/ articulated/ low floor
4.2. Materials used and methods of construction:
5. SPECIAL PROVISIONS FOR VEHICLES USED FOR THE CARRIAGE OF PASSENGERS
COMPRISING MORE THAN EIGHT SEATS IN ADDITION TO THE DRIVER'S SEAT
5.1. Class of vehicle (Class I, Class II, Class III, Class A, Class B):
5.2. Area for passengers (m ): .........................................................................................................
5.2.1. Total (S ): ..................................................................................................................................
5.2.2. Upper deck (S ): ...................................................................................................................
5.2.3. Lower deck (S ): ...................................................................................................................
5.2.4. For standing passengers (S ): ..................................................................................................
5.3. Number of passengers (seated and standing): .........................................................................
5.3.1. Total (N) : .............................................................................................................................
5.3.2. Upper deck (N ): ...............................................................................................................

Explanatory Notes:

3. MASSES AND DIMENSIONS (in kg and mm) (refer to drawing where applicable)
3.1. Wheel base(s) (fully loaded) : ...................................................................................................
3.2. Range of vehicle dimensions (overall)
3.2.1. For bodywork approved without chassis:
3.2.1.1. Length : ....................................................................................................................................
3.2.1.2. Width : .....................................................................................................................................
3.2.1.3. Height (in running order) (for suspension adjustable for height, indicate normal running
position): ....................................................................................................................................
4. BODYWORK
4.1. Type of bodywork: single deck/double deck/articulated/low floor
4.2. Materials used and methods of construction:
5. SPECIAL PROVISIONS FOR VEHICLES USED FOR THE CARRIAGE OF PASSENGERS
COMPRISING MORE THAN EIGHT SEATS IN ADDITION TO THE DRIVER'S SEAT
5.1. Class of vehicle (Class I, Class II, Class III, Class A, Class B):
5.1.1. Chassis type where the type-approved body can be installed (manufacturer(s)) and
vehicle(s) types):
5.2. Area for passengers (m ): .........................................................................................................
5.2.1. Total (S ): ..................................................................................................................................
5.2.1.1. Upper deck (S ): ...................................................................................................................
5.2.1.2. Lower deck (S ): ...................................................................................................................
5.2.2. For standing passengers (S ): ..................................................................................................
5.3. Number of passengers (seated and standing): .........................................................................
5.3.1. Total (N): .............................................................................................................................
5.3.2. Upper deck (N ): ...............................................................................................................
5.3.3. Lower deck (N ): ...............................................................................................................

Explanatory Notes:

2.3. Number of axles and wheels: ....................................................................................................
2.3.1. Number and position of axles with double wheels: ...................................................................
2.4. Chassis (if any) (overall drawing): .............................................................................................
2.5. Material used for the side-members : .....................................................................................
2.6. Position and arrangement of the engine: ..................................................................................
2.7. Hand of drive: ............................................................................................................................
2.7.1. Vehicle is equipped to be driven in right/left hand traffic.
3. MASSES AND DIMENSIONS (in kg and mm) (refer to drawing where applicable)
3.1. Wheel base(s) (fully loaded) : ...................................................................................................
3.2. Range of vehicle dimensions (overall)
3.2.1. For chassis with bodywork:
3.2.1.1. Length : ....................................................................................................................................
3.2.1.2. Width : .....................................................................................................................................
3.2.1.2.1. Maximum width: ........................................................................................................................
3.2.1.3. Height (in running order) (for suspensions adjustable for height, indicate normal running
position): ....................................................................................................................................
3.3. Mass of the vehicle with bodywork and, in the case of a towing vehicle of a category other
than M , with coupling device, if fitted by the manufacturer, in running order, or the mass of
the chassis or chassis with cab, without bodywork and/or coupling device if the
manufacturer does not fit the bodywork and/or coupling device (including liquids, tools,
spare wheel and driver, and, for buses and coaches, a crew member if there is a crew seat
in the vehicle): (maximum and minimum for each variant): ...................................................
3.3.1. Distribution of this mass among the axles and, in the case of a semi-trailer or centre axle
trailer, load on the coupling point (maximum and minimum for each variant): ..........................
3.4. Technically permissible maximum laden mass stated by the manufacturer (maximum and
minimum): ..................................................................................................................................
3.4.1. Distribution of this mass among the axles and, in the case of a semi-trailer or centre-axle
trailer, load on the coupling point (maximum and minimum): ....................................................
3.5. Technically permissible maximum mass/load on each axle: ....................................................

ANNEX 1 − PART 2 − APPENDIX 1
COMMUNICATION
(Maximum format: A4 (210 x 297mm))
issued by:
Name of administration:
.....................................
.....................................
.....................................
Concerning:
APPROVAL GRANTED
APPROVAL EXTENDED
APPROVAL REFUSED
APPROVAL WITHDRAWN
PRODUCTION DEFINITIVELY DISCONTINUED
Of a type of a vehicle/component/separate technical unit with regard to Regulation No. 107.
Approval Number: ................................ Extension No…: ..................................
SECTION I
1. Make (trade name of manufacturer): ..............................................................................................
2. Type: ...............................................................................................................................................
3. Means of identification of type if marked on the vehicle/component/separate technical unit
3.1. Location of that marking: .................................................................................................................
4. Category of vehicle ...................................................................................................................
5. Name and address of manufacturer: ..............................................................................................
6. In the case of components and separate technical units, location and method of affixing of the
type-approval mark: ........................................................................................................................
7. Address(es) of assembly plant(s): ..................................................................................................

1.7.4. Number of passengers seated: .......................................................................................................
1.7.4.1. Total (A) : ....................................................................................................................................
1.7.4.2. Upper deck (A )
1.7.4.3. Lower deck (A )
1.8. Volume of baggage compartments (m ): ........................................................................................
1.9. Area for baggage transportation on the roof (m ): ..........................................................................
1.10. Technical devices facilitating access to vehicles (ramp, lifting platform, kneeling-system): ...........
1.11. Position of centre of gravity of the laden vehicle in the longitudinal, transverse and vertical
directions: ........................................................................................................................................
2. Remarks: .........................................................................................................................................

SECTION II
1. Additional information (where applicable): see Addendum
2. Technical Service responsible for carrying out the tests: ...............................................................
3. Date of test report: ..........................................................................................................................
4. Number of test report: .....................................................................................................................
5. Remarks (if any): see Addendum
6. Place: ..............................................................................................................................................
7. Date: ................................................................................................................................................
8. Signature: ........................................................................................................................................
9. The index to the information package lodged with the Type Approval Authority, which may be
obtained on request, is attached.
1. Additional information
Addendum to Type-approval Certificate No. ……
concerning the Type-approval of a Bodywork as a Separate
Technical Unit with Regard to Regulation No. 107
1.1. Category of vehicle where the body can be installed (M , M ):
1.2. Bodywork concept (single/double deck, articulated, low-floor)
1.3. Chassis type(s) where the body can be installed: ...........................................................................
1.4. Number of passengers (seated and standing): ...............................................................................
1.4.1. Total (N) : ....................................................................................................................................
1.4.2. Upper deck (N ):
1.4.3. Lower deck (N ):
1.4.4. Number of passengers seated: .......................................................................................................
1.4.4.1. Total (A) : ....................................................................................................................................
1.4.4.2. Upper deck (A )
1.4.4.3. Lower deck (A )

ANNEX 1 − PART 2 − APPENDIX 3
COMMUNICATION
(Maximum format: A4 (210 x 297mm))
issued by:
Name of administration:
.....................................
.....................................
.....................................
Concerning:
APPROVAL GRANTED
APPROVAL EXTENDED
APPROVAL REFUSED
APPROVAL WITHDRAWN
PRODUCTION DEFINITIVELY DISCONTINUED
Of a type of a vehicle/component/separate technical unit with regard to Regulation No. 107.
Approval Number: ................................ Extension No…: ..................................
SECTION I
1. Make (trade name of manufacturer): ..............................................................................................
2. Type: ...............................................................................................................................................
3. Means of identification of type if marked on the vehicle/component/separate technical unit
3.1. Location of that marking: .................................................................................................................
4. Category of vehicle ...................................................................................................................
5. Name and address of manufacturer: ..............................................................................................
6. In the case of components and separate technical units, location and method of affixing of the
type approval mark: .........................................................................................................................
7. Address(es) of assembly plant(s): ..................................................................................................

ANNEX 2
ARRANGEMENTS OF APPROVAL MARKS
Model A
(See Paragraph 4.4 of this Regulation)
a = 8mm min
The above approval mark affixed to a vehicle shows that the vehicle type concerned has, with regard to
its constructional features, been approved in the Netherlands (E4) for Class III, pursuant to
Regulation No. 107 under approval number 042439. The approval number indicates that the approval
was granted according to the requirements of Regulation No. 107 as amended by the 04 series of
amendments.
Model B
(See Paragraph 4.5. of this Regulation)
a = 8mm min
The above approval mark affixed to a vehicle shows that the vehicle type concerned has been approved
in the Netherlands (E4) pursuant to Regulations Nos. 107 and 43 . The first two digits of the approval
numbers indicate that, on the dates on which these approvals were granted Regulation No. 107 included
the 04 series of amendments and Regulation No. 43 was in its original form.

1. - 6. (Reserved)
7. REQUIREMENTS
7.1. General
ANNEX 3
REQUIREMENTS TO BE MET BY ALL VEHICLES
7.1.1. If the driver's compartment is without a roof, the driver should have some special
protection against strong wind, sudden dust, heavy rain, etc.
7.2. Masses and Dimensions
7.2.1. The vehicles shall comply with the requirements of Annex 11.
7.2.2. Area Available for Passengers
7.2.2.1. The total surface area S available for passengers is calculated by deducting from the
total area of the floor of the vehicle:
7.2.2.1.1. The area of the driver's compartment;
7.2.2.1.2. The area of steps at doors and the area of any other step with a depth of less than
300mm and the area swept by the door and its mechanism when it is operated;
7.2.2.1.3. The area of any part over which the vertical clearance is less than 1,350mm measured
from the floor disregarding permitted intrusion specified in Paragraphs 7.7.8.6.3 and
7.7.8.6.4. of this Annex. In the case of vehicles of Class A or B, this dimension may be
reduced to 1,200mm;
7.2.2.1.4. The area of any part of the vehicle to which access by passengers is prevented as
defined in Paragraph 7.9.4. of this Annex.
7.2.2.1.5. The area of any space reserved solely for the carriage of goods or baggage and from
which passengers are excluded.
7.2.2.1.6. The area required to provide a clear working area at serveries;
7.2.2.1.7. The floor area occupied by any staircase, half staircase, intercommunication staircase
or the surface of any step.
7.2.2.2. The surface area S available for standing passengers (only in the case of vehicles of
Class A, I and II, in which the carriage of standing passengers is allowed) is calculated
by deducting from S :
7.2.2.2.1. The area of all parts of the floor in which the slope exceeds the maximum permissible
values as determined in Paragraph 7.7.6 of this Annex.
7.2.2.2.2. The area of all parts which are not accessible to a standing passenger when all the seats
are occupied, with the exception of folding seats;

7.2.2.4.3. With all possible wheelchair spaces occupied followed by the remaining area for
standing passengers and then the remaining seats available for use occupied.
7.2.3. Marking of Vehicles
7.2.3.1. Space shall be provided in the driver's area, in a position clearly visible to the driver in
his seating position, for the markings provided for in Paragraph 3.3 of Annex 11.
7.2.3.1.1. The maximum number of seating places the vehicle is designed to carry;
7.2.3.1.2. The maximum number of standing places, if any, the vehicle is designed to carry;
7.2.3.1.3. The maximum number of wheelchairs which the vehicle is designed to carry, if any.
7.2.3.2. (Reserved).
7.2.3.3. (Reserved)
7.3. Reserved
7.4. Stability Test
7.4.1. The stability of a vehicle shall be such that the point at which overturning occurs would
not be passed if the surface on which the vehicle stands were tilted to both sides in turn
to an angle of 28° from the horizontal.
7.4.2. For the purposes of the above test, the vehicle shall be at its mass in running order as
described in Paragraph 2.18 of this Regulation, with the addition of:
7.4.2.1. Loads equal to Q (as defined in Paragraph 3.2.3.2.1 of Annex 11) shall be placed on
each passenger seat (of the upper deck only in the case of double-deck vehicles).
If a single deck vehicle is intended for standees or with a crew member who is not
seated, the centre of gravity of the loads Q or 75kg representing them, shall be uniformly
distributed over the standee or crew area respectively, at a height of 875mm. If a double
deck vehicle is intended to be used with a crew member who is not seated, the centre of
gravity of the mass of 75kg representing the crew member shall be placed in the upper
deck gangway at a height of 875mm.
Where a vehicle is equipped to carry luggage on the roof, a uniformly distributed
mass (BX) of not less than that declared by the manufacturer in accordance with
Paragraph 3.2.3.2.1 of Annex 11, representing such baggage shall be secured to the
roof. The other baggage compartments shall not contain any baggage.

7.5.1.2. Precautions shall be taken, either by a suitable layout of the engine compartment or by
the provision of drainage orifices, to avoid, so far as possible, the accumulation of fuel,
lubricating oil or any other combustible material in any part of the engine compartment.
7.5.1.3. A partition of heat-resisting material shall be fitted between the engine compartment or
any other source of heat (such as a device designed to absorb the energy liberated
when a vehicle is descending a long gradient, e.g. a retarder, or a device for heating the
interior of the body other, however, than a device functioning by warm water circulation)
and the rest of the vehicle. All fixings, clips, gaskets, etc., used in conjunction with the
partition shall be fire resistant.
7.5.1.4. A heating device operating other than by hot water may be provided in the passenger
compartment if it is encased in material designed to resist the temperatures generated
by the device, emits no toxic fumes and is positioned such that no passenger is likely to
come into contact with any hot surface.
7.5.1.5. In the case of vehicles having the engine located to the rear of the driver's compartment,
the compartment shall be equipped with an alarm system providing the driver with both
an acoustic and a visual signal in the event of excess temperature in the engine
compartment and in each compartment where a combustion heater is located.
7.5.1.5.1. The alarm system shall be designed so as to detect a temperature in the engine
compartment, and in each compartment where a combustion heater is located in excess
of the temperature occurring during normal operation.
7.5.1.5.2. Paragraph 7.5.1.5.1. above is considered to be satisfied if the following areas of the
engine compartment, and each compartment where a combustion heater is located, are
monitored regarding excess temperature:
7.5.1.5.2.1. Areas in which, in case of leakage, flammable fluids (liquid or gas) may come into
contact with exposed components, e.g. the supercharger or the exhaust-system,
including engine mounted components, whose working temperature is equal to or
greater than the ignition temperature of the flammable fluids (liquid or gas);
7.5.1.5.2.2. Areas in which, in case of leakage, flammable fluids (liquid or gas) may come into
contact with shielded components, e.g. an independent heating device, whose working
temperature is equal to or greater than the ignition temperature of the flammable fluids
(liquid or gas); and
7.5.1.5.2.3. Areas in which, in case of leakage, flammable fluids (liquid or gas) may come into
contact with components, e.g. the alternator, whose temperature, in case of failure, may
be equal to or greater than the ignition temperature of the flammable fluids (liquid or
gas).
7.5.1.5.3. The alarm system shall be operational whenever the engine start device is operated,
until such time as the engine stop device is operated, regardless of the vehicle's attitude.
7.5.2. Electrical Equipment and Wiring
7.5.2.1. All cables shall be well insulated and all cables and electrical equipment shall be able to
withstand the temperature and humidity conditions to which they are exposed. In the
engine compartment, particular attention shall be paid to their suitability to withstand the
environmental temperature and the effects of all likely contaminants.

7.5.5. Materials
7.6. Exits
No flammable material shall be permitted within 100mm of the exhaust system
component, any high voltage electrical equipment or any other significant source of heat
unless the material is effectively shielded. Where necessary, shielding shall be provided
to prevent grease or other flammable materials coming into contact with exhaust system
or other significant heat sources. For the purposes of this Paragraph, a flammable
material is considered to be one which is not designed to withstand the temperatures
likely to be encountered in that location.
7.6.1. Number of Exits
7.6.1.1. The minimum number of doors in a vehicle shall be two, either two service doors or one
service door and one emergency door. Every double-deck vehicle shall have two doors
on the lower deck (see also Paragraph 7.6.2.2. below). The minimum number of service
doors required is as follows:
Number of passengers
Number of service doors
CLASS I & A CLASS II CLASS III & B
9 − 45 1 1 1
46 − 70 2 1 1
71 − 100
3
(2 in the case of a
double-deck vehicle)
2
1
>100 4 3 1
7.6.1.2. The minimum number of service doors in each rigid section of an articulated vehicle shall
be one except that this minimum number shall be two in the case of front section of an
articulated vehicle of Class I.
7.6.1.3. For the purpose of this requirement, service doors equipped with a power-operated
control system shall not be deemed to be emergency doors unless they can be readily
opened by hand, once the control prescribed in Paragraph 7.6.5.1 has been actuated, if
necessary.

7.6.1.7.2. One or two seats are permitted alongside the driver for additional people, in which case
both of the exits referred to in Paragraph 7.6.1.7.1. above shall be doors.
The driver's door shall be accepted as the emergency door for the occupants of those
seats, provided that it is possible to move a test gauge from the occupants' seats to the
exterior of the vehicle through the driver's door (see Annex 4, Figure 27).
Verification of the access to the driver's door shall be subject to the requirements of
Paragraph 7.7.3.2., by using the test gauge having a dimension of 600 × 400mm, as
described in Paragraph 7.7.3.3.
The door provided for the passengers shall be in the side of the vehicle opposite to that
containing the driver's door and shall be accepted as the emergency door for the driver.
Up to five additional seats may be fitted in a compartment incorporating the driver's
compartment, provided that the additional seats and the space for these seats comply
with all requirements of this Regulation and at least one door giving access to the
passenger compartment complies with the requirements of Paragraph 7.6.3. below for
emergency doors.
7.6.1.7.3. In the circumstances described in Paragraphs 7.6.1.7.1 and 7.6.1.7.2. above, the exits
provided for the driver's compartment shall not count as one of the doors required by
Paragraphs 7.6.1.1 to 7.6.1.2, nor as one of the exits required by Paragraph 7.6.1.4,
except in the case mentioned in Paragraphs 7.6.1.7.1 and 7.6.1.7.2. Paragraphs from
7.6.3 to 7.6.7, 7.7.1, 7.7.2 and 7.7.7. below shall not apply to such exits.
7.6.1.8. If the driver's compartment and seats adjacent to it are accessible from the main
passenger compartment by means of a passageway complying with one of the
conditions described in Paragraph 7.7.5.1.1. below, no external exit is required from the
driver's compartment.
7.6.1.9. If a driver's door or other exit from the compartment is provided in the circumstances
described in Paragraph 7.6.1.8. above it may only count as an exit for passengers
provided:
7.6.1.9.1. It satisfies the requirements relating to the dimensions of emergency door indicated in
Paragraph 7.6.3.1. below;
7.6.1.9.2. It fulfils the requirements indicated in Paragraph 7.6.1.7.2. above;
7.6.1.9.3. The space reserved for the driver's seat shall communicate with the main passengers'
compartment through an appropriate passage; such requirement shall be deemed to be
fulfilled if the test gauge described in Paragraph 7.7.5.1. below, can move unobstructed
from the gangway, until the front end of the gauge reaches the vertical plane tangential
to the foremost point of the driver's seat back (this seat being situated in its rearmost
longitudinal position) and, from this plane, the panel described in Paragraph 7.6.1.7.2.
above could be moved to the emergency door in the direction established by such
paragraph (see Annex 4, Figure 28) with seat and steering wheel adjustment in their mid
position.
7.6.1.10. Paragraphs 7.6.1.8 and 7.6.1.9. above do not preclude there being a door or other
barrier between the driver's seat and the passenger compartment provided that this
barrier can be released quickly by the driver in an emergency. A driver's door in a
compartment protected by such a barrier shall not be counted as an exit for passengers.

7.6.2.1.3. The provision of one or more additional service doors on the opposite side of the
vehicles in the case of vehicles designed for use in circumstances which require
loading/unloading on both sides. Examples of such circumstances include vehicles for
airside use at airports, vehicles for use on multimodal transport systems using island
platforms, or vehicles which cross borders to countries which do not drive on the same
side of the road as the country in which the vehicle is to be licensed for operation.
Vehicles so equipped shall be provided with control(s) which allow the driver to inhibit
normal operation of the doors which are not currently in use, or
7.6.2.1.4. The provision of a service door in the rear face of a Class A or B vehicle.
7.6.2.2. If the passenger's compartment has an area S equal or greater than 10m , two of the
doors referred to in Paragraph 7.6.1.1. above shall be separated such that the distance
between transverse vertical planes through their centres of area is not less than:
7.6.2.2.1. In the case of a single deck vehicle, 40% of the overall length of the passenger
compartment measured parallel to the longitudinal axis of the vehicle.
In the case of an articulated vehicle, this requirement shall be fulfilled if two doors of the
different sections are separated such that the distance between the doors is not less
than 40% of the overall length of the combined passenger compartment (all sections).
If one of these two doors forms part of a double door this distance shall be measured
between the two doors which are furthest apart.
7.6.2.2.2. In the case of a double deck vehicle, two of the doors referred to in Paragraph 7.6.1.1.
above shall be separated such that the distance between transverse vertical planes
through their centres of area is not less than either 25% of the overall length of the
vehicle or 40% of the overall length of the passenger compartment on the lower deck;
this shall not apply if the two doors are on different sides of the vehicle. If one of these
two doors forms part of a double door, this distance shall be measured between the two
doors which are furthest apart.
7.6.2.3. The exits (on each deck in the case of a double-deck vehicle) shall be placed in such a
way that their number on each of the two sides of the vehicle is substantially the same.
(This shall not imply the need to provide additional exits over and above the number
specified in Paragraph 7.6.1. above). Any exits in excess of the required minimum
number need not be substantially balanced on each of the two sides.
7.6.2.4. At least one exit shall be situated either in the rear face or in the front face of the vehicle
respectively. For Class I and A vehicles and for vehicles with a rear part permanently
closed off from the passenger compartment, this provision is fulfilled if an escape hatch
is fitted, or, if Paragraph 7.6.1.12. above applies, an additional exit to those specified in
Paragraph 7.6.1. above, is fitted on each side of the vehicle. For double-deck vehicles,
this requirement shall apply only to the upper deck.
7.6.2.5. The exits on the same side of the vehicle shall be suitably spaced out along the length of
the vehicle.
7.6.2.6. A door shall, provided that it is not a service door, be permitted in the rear face of the
vehicle.
7.6.2.7. If escape hatches are fitted, they shall be positioned as follows: if there is only one hatch,
it shall be situated in the middle third of the passenger compartment, if there are two
hatches, they shall be separated by a distance of at least 2m measured between the
nearest edges of the apertures in a line parallel to the longitudinal axis of the vehicle.

7.6.4.6. If the direct view is not adequate, optical or other devices shall be installed to enable the
driver to detect from his seat the presence of a passenger in the immediate interior and
exterior vicinity of every side service door which is not an automatically-operated service
door.
In the case of double-deck vehicles of Class I, this requirement also applies to the
interior of all service doors and to the immediate vicinity of each intercommunication
staircase on the upper deck.
In the case of a service door in the rear face of the vehicle not exceeding 22 passengers,
this requirement is satisfied if the driver is able to detect the presence of a person 1.3m
tall standing 1m behind the vehicle.
Driving mirrors may be used to meet the requirements of this Paragraph provided that
the field of view required for driving is still met.
In the case of doors situated behind the articulated section of an articulated vehicle,
mirrors shall not be deemed to be a sufficient optical device.
7.6.4.7. Every door which opens towards the interior of the vehicle and its mechanism shall be so
constructed that its movement is not likely to cause injury to passengers in normal
conditions of use. Where necessary, appropriate protection devices shall be fitted.
7.6.4.8. If a service door is located adjacent to a door to a toilet or other internal compartment the
service door shall be proofed against unintentional operation. However, this requirement
shall not apply if the door is locked automatically when the vehicle is moving at a speed
exceeding 5km/h.
7.6.4.9. In the case of vehicles having a capacity not exceeding 22 passengers, the service
doors of which are in the rear face of the vehicle, the leaves shall not be capable of
being opened more than 115° nor less than 85° and, when open, shall be capable of
being held automatically in that position. This does not preclude the ability to override
that stop and open the door beyond that angle when it is safe to do so; for example, to
enable reversing against a high platform for loading or to open the doors through 270° to
allow a clear loading area behind the vehicle.
7.6.4.10. The service door in any open position shall not obstruct the use of, or required access to,
any mandatory exit.
7.6.5. Additional Technical Requirements for Power-operated Service Doors
7.6.5.1. In the event of an emergency, every power-operated service door shall be capable,
when the vehicle is stationary or driving at a speed less than or equal to 5km/h, of being
opened from inside and, when not locked, from outside by controls which, whether or not
the power supply is operating:
7.6.5.1.1. Override all other door controls;
7.6.5.1.2. In the case of interior controls, are placed on, or within 300mm of, the door, at a height
(except in the case of interior controls for the door referred to in Annex 8,
Paragraph 3.9.1) of not less than 1,600mm above the first step;

7.6.5.6. The construction and control system of every power-operated service door shall be such
that a passenger is unlikely to be injured by the door or trapped in the door as it closes.
7.6.5.6.1. This requirement shall be considered satisfied if the following two requirements are met:
7.6.5.6.1.1. The first requirement is that when the closing of the door at any measuring point
described in Annex 6 is resisted by a clamping force not exceeding 150N, the door shall
reopen automatically to its fullest extent and, except in the case of an
automatically-operated service door, remain open until a closing control is operated. The
clamping force may be measured by any method to the satisfaction of the Type Approval
Authority. Guidelines are given in Annex 6 to this Regulation. The peak force may be
higher than 150N for a short time provided that it does not exceed 300N. The reopening
system may be checked by means of a test bar having a section of height 60mm, width
30mm with corners radiused to 5mm.
7.6.5.6.1.2. The second requirement is that whenever the doors are closed onto the wrist or fingers
of a passenger:
7.6.5.6.1.2.1. The door reopens automatically to its fullest extent and, except in the case of an
automatically-operated service door, remains open until a closing control is operated, or
7.6.5.6.1.2.2. The wrist or fingers can be readily extracted from the doors without risk of injury to the
passenger. This requirement may be checked by hand, or by means of the test bar
mentioned in Paragraph 7.6.5.6.1.1. above, tapered at one end over a length of 300mm
from a thickness of 30mm to a thickness of 5mm. It shall not be treated with polish nor
lubricated. If the door traps the bar it shall be capable of being easily removed, or
7.6.5.6.1.2.3. The door is maintained at a position allowing the free passage of a test bar having a
section of height 60mm, width 20mm, with corners radiused to 5mm. This position shall
not be more than 30mm distant from the fully closed position.
7.6.5.6.2. In the case of a front service door the requirement of Paragraph 7.6.5.6. above shall be
considered satisfied if the door:
7.6.5.6.2.1. Fulfils the requirements of Paragraphs 7.6.5.6.1.1 and 7.6.5.6.1.2. above, or
7.6.5.6.2.2. Is fitted with soft edges; these shall not, however be so soft that if the doors are closed
on the test bar mentioned in Paragraph 7.6.5.6.1.1. above the rigid structure of the doors
will reach the fully closed position.
7.6.5.7. Where a power-operated service door is held closed only by the continued application of
the power supply there shall be provided a visual warning device to inform the driver of
any failure in the power supply to the doors.
7.6.5.8. A starting prevention device, if fitted, shall be effective only at speeds of less than 5km/h
and shall be incapable of operation above that speed.
7.6.5.9. If the vehicle is not fitted with a starting prevention device, an audible warning to the
driver shall be activated if the vehicle is driven away from rest when any power-operated
service door is not fully closed. This audible warning shall be activated at a speed
exceeding 5km/h for doors complying with the requirements of Paragraph 7.6.5.6.1.2.3.
above.

7.6.6.3.4. After deactivation of the opening controls of the automatically-operated service doors by
the driver, open doors shall close in accordance with Paragraphs 7.6.6.3.1 and 7.6.6.3.2.
above.
7.6.6.4. Inhibition of the Automatic Closing Process on Doors Marked for Special Service, e.g. for
Passengers with Prams, Passengers with Reduced Mobility, etc.
7.6.6.4.1. The driver shall be able to inhibit the automatic closing process by actuation of a special
control. A passenger shall also be able to inhibit the automatic closing process directly
by pressing a special push-button.
7.6.6.4.2. The inhibition of the automatic closing process shall be indicated to the driver, e.g. by a
visual tell-tale.
7.6.6.4.3. Re-establishment of the automatic closing process shall in any case be capable of being
done by the driver.
7.6.6.4.4. Paragraph 7.6.6.3. above shall apply to the subsequent closing of the door.
7.6.7. Technical Requirements for Emergency Doors
7.6.7.1. Emergency doors shall be capable of being easily opened from inside and from outside
when the vehicle is stationary. However, this requirement shall not be construed as
precluding the possibility of locking the door from the outside, provided that the door can
always be opened from the inside by the use of the normal opening mechanism.
7.6.7.2. Emergency doors, during their use as such, shall not be of the power-operated type
unless, once the controls prescribed in Paragraph 7.6.5.1. above has been actuated and
returned to its normal position, the doors do not close again until the driver subsequently
operates a closing control. Activation of one of the controls in Paragraph 7.6.5.1. above
shall cause the door to open to a width that the gauge as defined in Paragraph 7.7.2.1.
below can pass through within a maximum of 8s after the operation of the control, or
enable the door to be easily opened by hand to a width that the gauge can pass through
within a maximum of 8s after the operation of the control. In addition emergency doors
shall not be of the sliding type except in the case of vehicles having a capacity not
exceeding 22 passengers. For these vehicles a sliding door, which has been shown to
be capable of being opened without the use of tools after a frontal barrier collision test in
accordance with Regulation No. 33, can be accepted as an emergency door.
7.6.7.3. Every control or device for opening an emergency door (on the lower deck in the case of
a double deck vehicle) from the outside shall be between 1,000mm and 1,500mm from
the ground and not more than 500mm from the door. In vehicles of Classes I, II and III
every control or device for opening an emergency door from the inside shall be between
1,000mm and 1,500mm from the upper surface of the floor or step nearest to the control
and be not more than 500mm from the door. This shall not apply to controls located
within the driver's area.
Alternatively, the control referred to in Paragraph 7.6.7.2. above for opening a poweroperated
door may be placed according to Paragraph 7.6.5.1.2. above.

7.6.8.6. Every hinged emergency window which is not clearly visible from the driver's seat shall
be fitted with an audible warning device to warn the driver when it is not completely
closed. The window lock, and not the movement of the window itself, shall actuate this
device.
7.6.9. Technical Requirements for Escape Hatches
7.6.9.1. Every escape hatch shall operate so as not to obstruct the clear passage from inside or
outside the vehicle.
7.6.9.2. Roof escape hatches shall be ejectable, hinged or made of readily-breakable safety
glass. Floor hatches shall be either hinged or ejectable and shall be fitted with an audible
warning device to warn the driver when it is not securely closed. The floor escape hatch
lock, and not the movement of the hatch itself, shall actuate this device. Floor escape
hatches shall be proofed against unintentional operation. However this requirement shall
not apply if the floor hatch is locked automatically when the vehicle is moving at a speed
exceeding 5km/h.
7.6.9.3. Ejectable types shall not become totally detached from the vehicle when operated such
that the hatch is not a danger to other road users. The operation of ejectable escape
hatches shall be such that inadvertent operation is effectively prevented. Floor ejectable
hatches shall eject only into the passenger compartment.
7.6.9.4. Hinged escape hatches shall hinge along the edge towards the front or rear of the
vehicle and shall hinge through an angle of at least 100°. Hinged floor escape hatches
shall hinge into the passenger compartment.
7.6.9.5. Escape hatches shall be capable of being easily opened or removed from the inside and
from the outside. However, this requirement shall not be construed as precluding the
possibility of locking the escape hatch for the purpose of securing the vehicle when
unattended, provided that the escape hatch can always be opened or removed from the
inside by the use of the normal opening or removal mechanism. In the case of a
readily-breakable hatch, a device shall be provided adjacent to the hatch, readily
available to persons inside the vehicle, to ensure that the hatch can be broken.
7.6.10. Technical Requirements for Retractable Steps
Retractable steps, if fitted shall comply with the following requirements:
7.6.10.1. The operation of retractable steps may be synchronised with that of the corresponding
service or emergency door;
7.6.10.2. When the door is closed no part of the retractable step shall project more than 10mm
beyond the adjacent line of the body work;
7.6.10.3. When the door is open and the retractable step is in the extended position, the surface
area shall conform to the requirements of Paragraph 7.7.7 of this Annex;
7.6.10.4. In the case of a power-operated step, it shall not be possible for the vehicle to move from
rest, under its own power, when the step is in the extended position. In the case of a
manually operated step, an audible indication shall alert the driver when the step is not
fully retracted.

7.6.12. Service-door Lighting
7.6.12.1. Service-door lighting may be provided to illuminate the flat, horizontal portion of the
ground defined in Paragraph 7.6.12.2.2. below. so as to aid passengers boarding and
alighting the vehicle and to enable the presence of a passenger within this portion of the
ground to be detected by the driver from his seat.
7.6.12.2. Service-door lighting, if fitted, shall:
7.6.12.2.1. Be of white colour;
7.6.12.2.2. Illuminate a flat, horizontal portion of the ground having a width of 2m measured from a
plane parallel to the median longitudinal vertical plane of the vehicle which passes
through the outermost point of the closed service door and over a length extending from
a transverse plane which passes through the foremost edge of the closed service door to
a transverse plane passing through the centre line of the foremost wheels situated to the
rear of the service door, or, in the case where there are no such wheels, to a transverse
plane passing through the rear of the vehicle;
7.6.12.2.3. Have limited dazzle outside a zone on the ground having a maximum width of 5m
measured from the side of the vehicle and a maximum length limited by a transverse
plane passing through the front of the vehicle and a transverse plane passing through
the rear of the vehicle;
7.6.12.2.4. If the lower edge of the lighting device is less than 2m from the ground, not project more
than 50mm beyond the overall width of the vehicle measured without this device and
have radii of curvature of not less than 2.5mm;
7.6.12.2.5. Be activated and deactivated manually by a separate switch, and
7.6.12.2.6. Be installed so that the device can only be switched on when a service door is operated
and the vehicle speed does not exceed 5km/h and is switched off automatically before
the vehicle reaches a speed exceeding 5km/h.
7.7. Interior Arrangements
7.7.1. Access to Service Doors (see Annex 4, Figure 1)
7.7.1.1. The free space extending inwards into the vehicle from the side wall in which the door is
mounted shall permit the free passage of one test gauge having the dimensions of either
test gauge 1 or test gauge 2 specified in Annex 4, Figure 1.
7.7.1.2. (Reserved).
The test gauge shall be maintained parallel with the door aperture as it is moved from
the starting position, where the plane of the face nearest to the interior of the vehicle is
tangential to the outermost edge of the aperture, to the position where it touches the first
step, after which it shall be kept at right angles to the probable direction of motion of a
person using the entrance.

7.7.1.9.2. Measured perpendicular to the longitudinal axis of the vehicle, there is a clearance of not
less than 300mm at any point and 550mm at any point being more than 1,200mm above
the floor or steps or less than 300mm below the ceiling (Annex 4, Figure 4).
7.7.1.10. The service door and emergency door dimensions in Paragraph 7.6.3.1 and the
requirements of Paragraphs 7.7.1.1 to 7.7.1.7, 7.7.2.1 to 7.7.2.3, 7.7.5.1 and 7.7.8.5. of
this Annex shall not apply to a vehicle of Class B with a technically permissible maximum
mass not exceeding 3.5t and up to 12 passenger seats in which each seat has
unobstructed access to at least two doors.
7.7.1.11. The maximum slope of the floor in the access passage shall not exceed 5%.
7.7.1.12. The surface of access passages shall be slip-resistant.
7.7.2. Access to Emergency Doors (see Annex 4, Figure 5)
The following requirements shall not apply to driver's doors used as emergency exits in
vehicles having a capacity not exceeding 22 passengers.
7.7.2.1. Except as provided for in Paragraph 7.7.2.4. below, the free space between the gangway
and the emergency door aperture shall permit the free passage of a vertical cylinder
300mm in diameter and 700mm high from the floor and supporting a second vertical
cylinder 550mm in diameter, the aggregate height of the assembly being 1,400mm.
The diameter of the upper cylinder may be reduced at the top to 400mm when a chamfer
not exceeding 30° from the horizontal is included.
7.7.2.2. The base of the first cylinder shall be within the projection of the second cylinder.
7.7.2.3. Where folding seats are installed alongside this passage, the free space for the cylinder
shall be required to be determined when the seat is in the position for use.
7.7.2.4. As an alternative to the dual cylinder, the gauging device described in Paragraph 7.7.5.1.
below may be used (see Annex 4, Figure 6).
7.7.3. Access to Emergency Windows
7.7.3.1. It shall be possible to move a test gauge from the gangway to the exterior of the vehicle
through every emergency window.
7.7.3.2. The direction of motion of the test gauge shall be in the direction in which a passenger
evacuating the vehicle would be expected to move. The test gauge shall be kept
perpendicular to that direction of motion.
7.7.3.3. The test gauge shall be in the form of a thin plate having a size of 600mm × 400mm with
corners radiused by 200mm. However, in the case of an emergency window in the rear
face of the vehicle, the test gauge may alternatively have a size of 1,400mm × 350mm
with corners radiused by 175mm.

7.7.5.1.1. If there is no exit forward of a seat or row of seats:
7.7.5.1.1.1. In the case of forward-facing seats, the front edge of the cylindrical gauge defined in
Paragraph 7.7.5.1. above shall reach at least until the transverse vertical plane
tangential to the foremost point of the foremost front row seat back and be retained in
that position. From this plane, it shall be possible to move the panel shown in Annex 4,
Figure 7, in such a way that starting from the contact position with the cylindrical gauge,
the panel side facing the exterior of the vehicle is displaced forwards a distance of
660mm.
7.7.5.1.1.2. In the case of sideways facing seats, the forward part of the cylindrical gauge shall reach
at least the transversal plane which coincides with a vertical plane passing through the
centre of the forward seat. (Annex 4, Figure 7).
7.7.5.1.1.3. In the case of rearward facing seats, the forward part of the cylindrical gauge shall reach
at least the transverse vertical plane tangential to the face of the seat cushions of the
forward row or seat (Annex 4, Figure 7).
7.7.5.2. (Reserved).
7.7.5.3. On vehicles of Class III the seats on one side or on both sides of the gangway may be
moveable laterally, it being then possible to reduce the width of the gangway to a figure
corresponding to a lower cylinder diameter of 220mm, on condition that the operation of
a control on each seat, readily accessible to a person standing in the gangway, shall be
sufficient to cause the seat to return easily and, if possible, automatically, even when it is
loaded, to the position corresponding to a minimum width of 300mm.
7.7.5.4. On articulated vehicles, the gauging device defined in Paragraph 7.7.5.1. above shall be
able to pass unobstructed through the articulated section on any deck where the two
sections permit through passage by passengers. No part of the soft covering of that
section, including parts of bellows, shall project into the gangway.
7.7.5.5. Steps may be fitted in the gangways. The width of such steps shall not be less than the
width of the gangway at the top of the steps.
7.7.5.6. Folding seats allowing passengers to sit in the gangway shall not be permitted. Folding
seats shall, however, be permitted in other areas of the vehicle so long as they do not
obstruct the passage down the gangway of the gangway test gauge when in the open
(seating) position.
7.7.5.7. Laterally-sliding seats which in one position encroach on the gangway shall not be
permitted except on vehicles of Class III and subject to the conditions prescribed in
Paragraph 7.7.5.3. above.
7.7.5.8. In the case of vehicles to which Paragraph 7.7.1.9. of this Annex applies, a gangway
shall not be necessary provided the access dimensions specified in that paragraph are
respected.
7.7.5.9. The surface of gangways shall be slip-resistant.

7.7.8. Passenger Seats (Including Folding Seats) and Space for Seated Passengers
7.7.8.1. Minimum Seat Width (see Annex 4, Figure 9)
7.7.8.1.1. The minimum width of the seat cushion, Dimension F (Annex 4, Figure 9), measured
from a vertical plane passing through the centre of that seating position, shall be:
7.7.8.1.1.1. 200mm in the case of Class I, II, A, B; or
7.7.8.1.1.2. 225mm in the case of Class III.
7.7.8.1.2. The minimum width of the available space for each seating position, Dimension G
(Annex 4, Figure 9), measured from a vertical plane passing through the centre of that
seating position at height between 270mm and 650mm above the uncompressed seat
cushion, shall be not less than:
7.7.8.1.2.1. 250mm in the case of Individual seats; or
7.7.8.1.2.2. 225mm in the case of continuous rows of seats for two or more passengers.
7.7.8.1.3. For vehicles not exceeding a width of 2.35m:
7.7.8.1.3.1. The width of the available space for each seating position, measured from a vertical
plane passing through the centre of that seating position at heights between 270mm and
650mm above the uncompressed seat cushion, shall be 200mm (see Annex 4,
Figure 9A). In case of compliance with this Paragraph the requirements of
Paragraph 7.7.8.1.2. above shall not apply; and
7.7.8.1.3.2. In the case of vehicles of Class III, the minimum width of the seat cushion, Dimension "F"
(Annex 4, Figure 9A), measured from a vertical plane passing through the centre of that
seating position, shall be a minimum of 200mm. In case of compliance with this
Paragraph the requirements of Paragraph 7.7.8.1.1.2. above shall not apply.
7.7.8.1.4. For vehicles having a capacity not exceeding 22 passengers, in the case of seats
adjacent to the wall of the vehicle, the available space does not include, in its upper part,
a triangular area 20mm wide by 100mm high (see Annex 4, Figure 10). In addition, the
space needed for safety belts and their anchorages and for the sun visor should be
considered as exempted.
7.7.8.1.5. In measuring the gangway width, no account shall be taken of whether or not the
available space defined above protrudes into the gangway.
7.7.8.2. Minimum Depth of Seat Cushion (Dimension K, see Annex 4, Figure 11)
The minimum depth of a seat cushion shall be:
7.7.8.2.1. 350mm in vehicles of Class I, A or B, and
7.7.8.2.2. 400mm in vehicles of Class II or Class III.

7.7.8.5.2. For a seat behind a seat and/or a seat facing the gangway, a minimum clear foot space
of at least 300mm depth and a width according to Paragraph 7.7.8.1.1. of this Annex,
shall be provided as shown in Annex 4, Figure 11b. The local presence in this space of
seat legs, passenger footrests and of intrusions as provided by Paragraph 7.7.8.6. below
shall be permitted provided that adequate space remains for the passengers' feet. This
foot space may partly be situated in and/or above the gangway but shall not create any
obstruction when measuring the minimum gangway-width in accordance with
Paragraph 7.7.5. In the case of seats alongside the driver's seat in vehicles of Class A or
B, intrusion of the seat belts and seat belt anchorages shall be allowed.
7.7.8.5.3. The minimum number of priority seats complying with the requirements of Annex 8,
Paragraph 3.2. shall be four in Class I, two in Class II and one in Class A. In the case of
vehicles of Class III or Class B, subject to the requirements of Annex 8, the minimum
number of priority seats shall be two in Class III and one in Class B.
A seat that folds out of the way when not in use shall not be designated as a priority
seat.
7.7.8.6. Free Height Over Seating Positions
7.7.8.6.1. In the case of single deck vehicles, over each seating position and, except in the case of
the seat(s) alongside the driver in a vehicle of Class A or B, its associated foot space,
there shall be measured a free space with a height of not less than 900mm measured
from the highest point of the uncompressed seat cushion and at least 1,350mm from the
mean level of the floor in the foot space. In the case of vehicles to which
Paragraph 7.7.1.10 of this Annex applies, and also for the seat(s) alongside the driver in
a vehicle of Class A or B, these dimensions may be reduced to 1,200mm measured from
the floor and 800mm measured from the highest point of the uncompressed seat
cushion.
In the case of double deck vehicles, each seating position shall have a free height of not
less than 900mm measured from the highest point of the uncompressed seat cushion. In
the case of the upper deck, this free height may be reduced to 850mm.
7.7.8.6.2. This free space shall be extended over the zone defined:
7.7.8.6.2.1. By longitudinal vertical planes 200mm either side of the median vertical plane of the
seating position, and
7.7.8.6.2.2. By a transverse vertical plane through the rearmost upper point of the seat back and by
a transverse vertical plane 280mm in front of the foremost point of the uncompressed
seat cushion, measured in each case at the median vertical plane of the seating position.
7.7.8.6.3. From the edges of the free space defined in Paragraph 7.7.8.6.1 and 7.7.8.6.2. above,
the following zones may be excluded:
7.7.8.6.3.1. In the case of the upper part of the outboard seats, adjacent to the inner wall of the
vehicle, a zone with a rectangular cross-section 150mm in height and 100mm in width
(see Annex 4, Figure 14).
7.7.8.6.3.2. In the case of the upper part of outboard seating position, a zone with triangular
cross-section whose apex is situated 700mm from the top and whose base is 100mm in
width (see Annex 4, Figure 15). The space needed for safety belts and their anchorages
and for the sun visor is also excluded.

7.7.9.3. Communication with the Toilet Compartment
Toilet compartments shall be fitted with a means of summoning assistance in an
emergency.
7.7.10. Hot Drink Machines and Cooking Equipment
7.7.10.1. Hot drink machines and cooking equipment shall be so installed or guarded that no hot
food or drink is likely to be spilled on any passenger due to emergency braking or
cornering forces.
7.7.10.2. On vehicles fitted with hot-drink machines or cooking equipment, all passenger seats
shall have adequate provision for setting down hot food or drink whilst the vehicle is in
motion.
7.7.11. Doors to Interior Compartments
Every door to a toilet or other interior compartment:
7.7.11.1. Shall be self-closing, and shall not be fitted with any device to hold it open if, when open,
it could obstruct passengers in an emergency.
7.7.11.2. Shall, when open, not conceal any handle, control device for opening or obligatory
marking associated with any service door, emergency door, emergency exit, fire
extinguisher or first aid kit;
7.7.11.3. Shall be provided with a means to enable the door to be opened from outside the
compartment in an emergency.
7.7.11.4. Shall not be capable of being locked from the outside unless it can always be opened
from the inside.
7.7.12. Intercommunication Staircase of a Double-deck Vehicle (see Annex 4, Figure 1)
7.7.12.1. The minimum width of any intercommunication staircase shall be so designed as to
permit the free passage of the single door access template as defined in Figure 1 of
Annex 4. The panel shall be moved starting from the gangway of the lower deck up to
the last step, in the probable direction of motion of a person using the staircase.
7.7.12.2. Intercommunication staircases shall be so designed, that, during heavy braking of the
vehicle moving in the forward direction, there is no danger of a passenger being
projected downwards.
This requirement is considered to be fulfilled if at least one of the following conditions is
met:
7.7.12.2.1. No part of the staircase is forward descending;
7.7.12.2.2. The staircase is equipped with guards or a similar provision;
7.7.12.2.3. There is an automatic device in the upper part of the staircase which prevents the use of
the staircase when the vehicle is in motion; this device shall be easily operable in an
emergency.

7.7.14.3. The minimum width of the seat cushion, (Dimension F, see Annex 4, Figure 9) measured
from a vertical plane passing through the centre of the seat, shall be:
7.7.14.3.1. 200mm in the case of Class A or B;
7.7.14.3.2. 225mm in the case of Class I, II or III.
7.7.14.4. The minimum depth of the seat cushion, (Dimension K, see Annex 4, Figure 11a)
measured from a vertical plane passing through the centre of the seat, shall be:
7.7.14.4.1. 350mm in the case of Class A or B;
7.7.14.4.2. 400mm in the case of Class I, II or III.
7.7.14.5. The minimum overall width of the seat back measured up to a height of 250mm above
the horizontal plane tangential to the uppermost surface of the uncompressed seat
cushion shall be 450mm.
7.7.14.6. The distance between armrests shall ensure a free space for the driver, as defined in
Paragraph 7.7.14.2. above, of not less than 450mm.
7.7.14.7. The seat shall be adjustable in its longitudinal and vertical positions and in its seat back
inclination. It shall lock automatically in the selected position and, if fitted with a
swivelling mechanism, it shall lock automatically when in the driving position. The seat
shall be equipped with a suspension system.
7.7.14.7.1. The suspension system and the vertical position adjustment are not mandatory for
vehicle of Class A or B.
7.8. Artificial Interior Lighting
7.8.1. Internal electrical lighting shall be provided for the illumination of:
7.8.1.1. All passenger compartments, crew compartments, toilet compartments and the
articulated section of an articulated vehicle;
7.8.1.2. Any step or steps;
7.8.1.3. The access to any exits and the area immediately around the service door(s) including,
when in use, any boarding device fitted;
7.8.1.4. The internal markings and internal controls of all exits;
7.8.1.5. All places where there are obstacles.
7.8.1.6. In the case of a double-decked vehicle without a roof, at least one lighting device shall
be provided as near as practicable to the top of every staircase leading to the upper
deck.
7.8.2. There shall be at least two internal lighting circuits such that failure of one will not affect
the other. A circuit serving only permanent entry and exit lighting can be considered as
one of these circuits.
7.8.3. (Reserved)

7.11.1.3. Handrails and handholds shall be of a section enabling passengers to grasp them easily
and firmly. Every handrail shall provide a length of at least 100mm to accommodate a
hand. No dimension of the section shall be smaller than 20mm or greater than 45mm
except in the case of handrails on doors and seats and, in the case of a vehicle of
Class II, III or B, in access passages. In these cases handrails having a minimum
dimension of 15mm shall be permitted provided that one other dimension is of at least
25mm. Handrails shall not have sharp bends.
7.11.1.4. The clearance between a handrail or handhold, along the majority of its length, and the
adjacent part of the vehicle body or walls shall be least 40mm. However, in the case of a
handrail on a door or a seat, or in the access passage of a vehicle of Class II, III or B, a
minimum clearance of 35mm shall be permitted.
7.11.1.5. The surface of every handrail, handhold or stanchion shall contrast visually with their
immediate surroundings and be slip-resistant.
7.11.2. Additional Requirements for Handrails and Handholds for Vehicles Designed to Carry
Standing Passengers
7.11.2.1. Handrails and/or handholds shall be provided in sufficient number for each point of the
floor area intended, in conformity with Paragraph 7.2.2. of this Annex for standing
passengers. For this purpose, strap hangers, if fitted, may be counted as handholds,
provided that they are held in their position by suitable means. This requirement shall be
deemed to be fulfilled if, for all possible sites of the testing device shown in Annex 4,
Figure 20 hereto, at least two handrails or handholds can be reached by the device's
moveable arm. The testing device may be freely turned about its vertical axis.
7.11.2.2. When applying the procedure described in Paragraph 7.11.2.1. above, only such
handrails and handholds shall be considered which are not less than 800mm and not
more than 1,950mm above the floor.
7.11.2.3. For every position that can be occupied by a standing passenger, at least one of the two
required handrails or handholds shall be not more than 1,500mm above the level of the
floor at that position. This does not apply to an area adjacent to a door where the door or
its mechanism in open position would prevent the use of this handhold. Also, exception
may be given in the middle of large platforms, but the sum of these exceptions shall not
exceed 20% of the total standing area.
7.11.2.4. Areas which can be occupied by standing passengers and are not separated by seats
from the side walls or rear wall of the vehicle shall be provided with horizontal handrails
parallel to the walls and installed at a height of between 800mm and 1,500mm above the
floor.
7.11.3. Handrails and Handholds for Service Doors
7.11.3.1. Door apertures shall be fitted with handrails and/or handholds on each side. In the case
of double doors this requirement can be fulfilled by fitting one central stanchion or one
central handrail.

7.13. Baggage Racks and Occupant Protection
The occupants of the vehicle shall be protected from objects liable to fall from baggage
racks under braking or cornering forces. If baggage compartments are fitted, they shall
be designed in such a way that baggage is prevented from falling in the event of sudden
braking.
7.14. Trap Doors, if Fitted
7.14.1. Every trap door, that is not an escape hatch, on the floor of a vehicle shall be so fitted
and secured that it cannot be dislodged or opened without the use of tools or keys and
no lifting or securing device shall project by more than 8mm above floor level. Edges of
projections shall be rounded.
7.15. Visual Entertainment
7.15.1. Forms of visual entertainment for passengers, for example television monitors or videos,
shall be located out of the driver's view when the driver is seated in his normal driving
position. This shall not preclude any television monitor or similar device used as part of
the driver's control or guidance of the vehicle, for example to monitor service doors.
7.16. Trolleybuses
7.16.1. Trolleybuses shall meet the provisions of Annex 12.
7.17. Passenger Protection in Vehicles without a Roof
Every vehicle without a roof shall have:
7.17.1. A continuous front panel over the full width of that part of the vehicle that does not have
a roof, with a height of not less than 1,400mm from the general level of the floor adjacent
to the front panel;
7.17.2. A continuous protection around the side and rear of that part of the vehicle that does not
have a roof, with a height of not less than 1,100mm at the sides and 1,200mm at the rear
of the vehicle, measured from the general level of the floor adjacent to the panels. The
protection shall consist of continuous side and rear panels with a height of not less than
700mm from the general level of the floor adjacent to the panels, combined with one or
more continuous guard rail(s) that fulfils the following characteristics:
(a)
(b)
(c)
(d)
No dimension of its section shall be less than 20mm, or more than 45mm;
The size of any aperture between a guard rail and any adjacent guard rail or panel
shall not exceed 200mm;
It shall be firmly attached to the structure of the vehicle;
Doors at exits shall be considered to form part of this protection.
7.18. Vision and Communication Aid
In the case of a vehicle without a roof, the driver shall be provided with a visual means,
such as a mirror, periscope or video camera/monitor, to enable the behaviour of
passengers in the area without a roof to be observed. In addition, an intercommunication
system shall be provided to enable the driver to communicate with these passengers.

ANNEX 4
EXPLANATORY DIAGRAMS
Vehicle class
Height of the upper panel (mm)
(Dimension "A" Figure 1)
Test gauge 1 Test gauge 2
Class A 950 950
Class B 700 950
Class I 1,100 1,100
Class II 950 1,100
Class III 850 1,100
Figure 1
Access to Service Doors
(see Annex 3, Paragraph 7.7.1)

Figure 3
Determination of Unobstructed Access to Door
(see Annex 3, Paragraph 7.7.1.9.1)
Figure 4
Determination of Unobstructed Access to Door
(see Annex 3, Paragraph 7.7.1.9.2)

Figure 6
Gangway Mannequin
(see Annex 3, Paragraph 7.7.5.)

Figure 7
Forward Limitation of the Gangway
(see Annex 3, Paragraph 7.7.5.1.1.1)

G (mm) minimum
F (mm) min
Continuous seats
Individual seats
200
225
250
Figure 9
Width of Passenger Seats
(see Annex 3, Paragraph 7.7.8.1.)
G (mm) minimum
F (mm) min
Continuous seats
Individual seats
200
200
200
Figure 9A
Width of Passenger Seats
(see Annex 3, Paragraph 7.7.8.1.3)

H = 400/500mm
K = 350mm min
Figure 11a
Seat-cushion Depth and Height
(see Annex 3, Paragraphs 7.7.8.2 and 7.7.8.3)

Figure 13
Space for Seated Passengers behind a Partition or other Rigid Structure other than a Seat
(see Annex 3, Paragraph 7.7.8.5.1)

I (mm)
400 to 500
(for Classes A, B, I and II min 350mm at wheel
arches and engine compartment(s))
Figure 15
Permitted Intrusion above a Seating Position
(see Annex 3, Paragraph 7.7.8.6.3.2)

Figure 17
Permitted Intrusion at Rear Corner Seats
View of the Prescribed Area of the Seat (Two Side Seats at the Rear)
(see Annex 3, Paragraph 7.7.8.6.3.4)

Thickness 20mm
Figure 20
Testing Device for Siting of Handholds
(see Annex 3, Paragraph 7.11.2.1)

Figure 23
Accessibility Symbols
(see Annex 8, Paragraphs 3.2.8 and 3.6.6)
Colour:
Size:
blue basis with white symbol
at least 130mm diameter
Reference for the design principles of safety symbols: ISO 3864-1:2002
Figure 23A
Pictogram for Wheelchair Users
Colour:
Size:
blue basis with white symbol
at least 130mm diameter
Reference for the design principles of safety symbols: ISO 3864-1:2002
Figure 23B
Pictogram for Passengers with Reduced Mobility other than Wheelchair Users

Figure 27
Access to Driver's Door
(see Annex 3, Paragraph 7.6.1.7.2)
Figure 28
Access to Driver's Door
(see Annex 3, Paragraph 7.6.1.9.3)

Figure 30

2.5. The relation between the above parameters is shown in Figure 1 below (as an example):
Figure 1
2.6. Clamping or mean reactive force F is the arithmetical mean value of the effective forces,
measured at the same measuring point subsequently more times:
F
=

( F )
n
i
3. MEASUREMENTS
3.1. Conditions of measurement:
3.1.1. Temperature range: 10° − 30°C
3.1.2. The vehicle shall be standing on a horizontal surface. In the case of ramp measurements, this
surface shall be fitted with a rigidly mounted block or other similar device having a face against
which the ramp can react.
3.2. Measurements points shall be:
3.2.1. In the case of doors:
3.2.1.1. At the main closing edges of the door:
one in the middle of the door;
one 150mm above the lower edge of the door.
3.2.1.2. If equipped with clamping prevention devices for the opening process:
At the secondary closing edges of the door at that point which is considered to be the most
dangerous place of clamping.

4.2.2. The stiffness of the load cell shall be 10 ± 0.2 N/mm. The maximum spring deflection shall be
limited to 30mm so that a maximum peak force of 300N is achieved.
Figure 2

1.1.1. A vehicle to which Paragraph 7.7.1.10. of Annex 3 applies shall meet the requirements of
Paragraph 7.6.3.1. of Annex 3 or Paragraph 1.1. of this Annex as regards emergency windows
and escape hatches, and the following minimum requirements as regards service doors and
emergency doors:
Aperture Dimensions Remarks
Service door
Emergency
door
Aperture Height:
1,100mm
Width:
Single door:
650mm
Double door:
1,200mm
Height: 1,100mm
Width: 550mm
This dimension may be reduced by a radius at the corners
of the aperture not exceeding 150mm.
This dimension may be reduced by a radius at the corners
of the aperture not exceeding 150mm. The width may be
reduced by 100mm when the measurement is made at the
level of the handholds and by 250mm in cases where
intruding wheel arches or the actuating mechanism for
automatic or remote-control doors or the rake of the
windscreen so require.
The width may be reduced to 300mm in cases where
intruding wheel arches so require, providing that the width
of 550mm is respected at the minimum height of 400mm
above the lowest part of the door aperture. The upper
corners may be reduced with round-offs with a radius of
not more than 150mm.
1.2. Siting of Exits
1.2.1. The service door(s) shall be situated on the side of the vehicle that is nearer to the side of the
road corresponding to the direction of the traffic in the country in which the vehicle is to be
registered, or in the rear face of the vehicle.
1.2.2. The exits shall be placed in such a way that there is at least one exit on each side of the vehicle.
1.2.3. The forward half and the rearward half of the passenger space shall each contain at least one
exit.
1.2.4. At least one exit shall be situated either in the rear face or in the front face of the vehicle unless
an escape hatch is fitted.

3.2.5. The height of the uncompressed seat cushion relative to the floor shall be such that the
distance from the floor to a horizontal plane tangent to the front upper surface of the seat
cushion is between 400mm and 500mm.
3.2.6. The foot space at priority seating positions shall extend forward of the seat from a
vertical plane through the forward edge of the seat cushion. The foot space shall not
have a slope in any direction of more than 8%. For vehicles of Classes I and A, the
vertical distance between the floor of the seating area and the adjacent gangway shall be
not more than 250mm.
3.2.7. Each priority seating position shall have a free height of not less than 1,300mm for
vehicles of Class I and A and 900mm for vehicles of Class II, measured from the highest
point of the uncompressed seat cushion. This free height shall extend over the vertical
projection of the minimum required seat width of 440mm and the associated foot space
Intrusion of a seat back or other object into this space shall be permitted provided that a
minimum clear vertical space extending 230mm in front of the seat cushion is
maintained. Where the priority seat is positioned facing a bulkhead more than 1,200mm
in height this space shall be 300mm. From the edges of the free space defined above,
intrusions are permitted in accordance with Paragraphs 7.7.8.6.3.1 to 7.7.8.6.3.4 of
Annex 3 as if reference to the clear space in Paragraphs 7.7.8.6.1 and 7.7.8.6.2 of
Annex 3 is a reference to the clear space defined above. The provisions of
Paragraph 7.7.8.1.4 of Annex 3 may apply. Intrusions of handholds or handrails as
mentioned in Paragraph 3.4.2. below may protrude by a maximum of 100mm from the
sidewall into the clear space over the vertical projection of the foot space.
3.2.8. Vehicles fitted with a priority seat shall have pictogram(s) in accordance with Annex 4,
Figure 23B visible from the outside, both on the front nearside of the vehicle and
adjacent to the relevant service door(s). A pictogram shall be placed internally adjacent
to the priority seat.
3.3. Communication Devices
3.3.1. Communication devices shall be placed adjacent to any priority seat and within any
wheelchair area and shall be at a height between 700mm and 1,200mm above the floor.
3.3.2. Communication devices situated in the low floor area shall be at a height between
800mm and 1,500mm where there are no seats.
3.3.3. (Reserved)
3.3.4. If a vehicle is fitted with a ramp or lift, a means of communication with the driver shall be
fitted outside, adjacent to the door, and at a height between 850mm and 1,300mm from
the ground. This requirement shall not apply to a door situated in the direct field of vision
of the driver.

3.6.4.1. By "moving freely and easily", it is meant that there exists:
(a)
(b)
Sufficient space available for the wheelchair user to manoeuvre without the
assistance of a person;
There are no steps, gaps or stanchions which could be an obstacle to the free
movement of the wheelchair user.
3.6.4.2. For the application of the above provisions, the test shall be performed, in the case of
vehicles of Class I and A fitted with more than one wheelchair space, for each
wheelchair space with all other wheelchair spaces occupied by the reference wheelchair.
3.6.5. In vehicles of Class I and A fitted with a ramp for wheelchair access, it shall be possible
for a reference wheelchair having the dimensions shown in Annex 4, Figure 21 to enter
and exit a vehicle with the wheelchair moving in a forward direction.
3.6.6. Vehicles fitted with a wheelchair space shall have pictogram(s) in accordance with
Annex 4, Figure 23A visible from the outside, both on the front nearside of the vehicle
and adjacent to the relevant service door(s).
One of these pictograms shall be placed internally adjacent to each wheelchair space
indicating whether the wheelchair is to be positioned facing the front or the rear of the
vehicle.
3.7. Seats and Standing Passengers in the Wheelchair Space
3.7.1. Folding seats may be fitted in a wheelchair space. However, such seats when folded and
out of use shall not intrude into the wheelchair space.
3.7.2. A vehicle may be equipped with demountable seats fitted in the wheelchair space
provided that such seats may be easily removed by the driver or a crew member.
3.7.3. For vehicles of Class I, II and A, where the foot space of any seat, or part of a folding
seat when in use, intrudes into a wheelchair space, those seats shall have signs fixed on
or adjacent to them with the following text, equivalent text or pictogram:
"Please give up this space for a wheelchair user".
The provisions of Paragraph 7.6.11.4. of Annex 3 apply to any textual markings used.
3.7.4. In vehicles where any wheelchair space is designated for use exclusively by a
wheelchair user as provided for in Paragraph 7.2.2.2.10. of Annex 3, those spaces shall
be clearly marked with the following text, equivalent text or pictogram:
"Area designated for use exclusively by a wheelchair user"
The provisions of Paragraph 7.6.11.4. of Annex 3 apply to any textual markings used.

3.8.2.4.2. For Category M :
3.8.2.4.2.1. 740daN ± 20daN in the case of a lap belt. The force shall be applied on the wheelchair
user restraint system in the horizontal plane of the vehicle and towards the front of the
vehicle if the restraint system is not attached to the floor of the vehicle. If the restraint
system is attached to the floor, the force shall be applied in an angle 45° ± 10° to the
horizontal plane of the vehicle and towards the front of the vehicle;
3.8.2.4.2.2. 450daN ± 20daN in the horizontal plane of the vehicle and towards the front of the
vehicle on the lap portion of the belt and 450daN ± 20daN in the horizontal plane of the
vehicle and towards the front of the vehicle on the torso portion of the belt in the case of
3-point belt;
3.8.2.4.2.3. 1,130daN ± 20daN in an angle of 45° ± 10° to the horizontal plane of the vehicle and
towards the front of the vehicle on the wheelchair restraint system;
3.8.2.4.2.4. The forces shall be applied simultaneously.
3.8.2.5. In forward direction in the case of a combined wheelchair and wheelchair user restraint
system.
3.8.2.5.1. For Category M ;
3.8.2.5.1.1. 1,110daN ± 20daN in an angle of 45° ± 10° to the horizontal plane of the vehicle and
towards the front of the vehicle on the wheelchair user restraint system in the case of a
lap belt;
3.8.2.5.1.2. 675daN ± 20daN in an angle of 45° ± 10° to the horizontal plane of the vehicle and
towards the front of the vehicle on the lap portion of the belt and 675daN ± 20daN in the
horizontal plane of the vehicle and towards the front of the vehicle on the torso portion of
the belt in the case of 3-point belt;
3.8.2.5.1.3. 1,715daN ± 20daN in an angle of 45° ± 10° to the horizontal plane of the vehicle and
towards the front of the vehicle on the wheelchair restraint system;
3.8.2.5.1.4. The forces shall be applied simultaneously.
3.8.2.5.2. For Category M :
3.8.2.5.2.1. 740daN ± 20daN in an angle of 45° ± 10° to the horizontal plane of the vehicle and
towards the front of the vehicle on the wheelchair user restraint system in the case of a
lap belt;
3.8.2.5.2.2. 450daN ± 20daN in an angle of 45° ± 10° to the horizontal plane of the vehicle and
towards the front of the vehicle on the lap portion of the belt and 450daN ± 20daN in the
horizontal plane of the vehicle and towards the front of the vehicle on the torso portion of
the belt in the case of 3-point belt;
3.8.2.5.2.3. 1,130daN ± 20daN in an angle of 45° ± 10° to the horizontal plane of the vehicle and
towards the front of the vehicle on the wheelchair restraint system;
3.8.2.5.2.4. The forces shall be applied simultaneously.

3.8.3.6.3. The forces in Paragraph 3.8.3.6.1. above and Paragraph 3.8.3.6.2. shall be applied
simultaneously in the forward direction and at an angle of 10° ± 5° above the horizontal
plane;
3.8.3.6.4. The forces in Paragraph 3.8.3.6.1. above shall be applied in the rearward direction and
at an angle of 10° ± 5° above the horizontal plane;
3.8.3.6.5. The forces shall be applied as rapidly as possible through the central vertical axis of the
wheelchair space; and
3.8.3.6.6. The force shall be maintained for a period of not less than 0.2s.
3.8.3.6.7. The test shall be carried out on a representative section of the vehicle structure together
with any fitting provided in the vehicle which is likely to contribute to the strength or
rigidity of the structure.
3.8.3.7. The forces specified in Paragraph 3.8.3.6. above are:
3.8.3.7.1. In the case of anchorages provided for a wheelchair restraint system fitted to a
Category M vehicle:
3.8.3.7.1.1. 1,110daN ± 20daN applied in the longitudinal plane of the vehicle and towards the front
of the vehicle at a height of not less than 200mm and not more than 300mm measured
vertically from the floor of the wheelchair space, and
3.8.3.7.1.2. 550daN ± 20daN applied in the longitudinal plane of the vehicle and towards the rear of
the vehicle at a height of not less than 200mm and not more than 300mm measured
vertically from the floor of the wheelchair space;
3.8.3.7.2. In the case of anchorages provided for a wheelchair restraint system fitted to a
Category M vehicle
3.8.3.7.2.1. 740daN ± 20daN applied in the longitudinal plane of the vehicle and towards the front of
the vehicle at a height of not less than 200mm and not more than 300mm measured
vertically from the floor of the wheelchair space, and
3.8.3.7.2.2. 370daN ± 20daN applied in the longitudinal plane of the vehicle and towards the rear of
the vehicle at a height of not less than 200mm and not more than 300mm measured
vertically from the floor of the wheelchair space;
3.8.3.7.3. In the case of anchorages provided for a wheelchair user restraint system the forces
shall be in accordance with the requirements of Regulation No. 14. The forces shall be
applied by means of a traction device as appropriate to the belt type as specified in
Regulation No. 14.
3.8.3.8. A wheelchair restraint system shall be subject to a dynamic test carried out in
accordance with the following requirements:
3.8.3.8.1. A representative wheelchair test trolley of mass 85kg shall, from a speed of between
48km/h to 50km/h to rest, be subject to a deceleration-time pulse:
3.8.3.8.1.1. Exceeding 20g in the forward direction for a cumulative period of at least 0.015s;

3.8.4. Rearward-facing Wheelchair − Static Test Requirements
3.8.4.1. Vehicles not required to have occupant restraint systems fitted may, as an alternative to
the provisions of Paragraph 3.8.2 or 3.8.3. above, be provided with a wheelchair space
designed for the wheelchair user to travel unrestrained with the wheelchair facing
rearwards against a support or backrest, in accordance with the following provisions:
3.8.4.1.1. One of the longitudinal sides of the space for a wheelchair shall rest against a side or
wall of the vehicle or a partition;
3.8.4.1.2. A support or backrest perpendicular to the longitudinal axis of the vehicle shall be
provided in the forward end of the wheelchair space;
3.8.4.1.3. The support or backrest shall be designed for the wheels or the back of the wheelchair to
rest against the support or backrest in order to avoid the wheelchair from tipping over and
shall comply with the provisions of Paragraph 3.8.5. below;
3.8.4.1.4. A handrail or handhold shall be fitted to the side or wall of the vehicle or a partition in such
a way to allow the wheelchair user to grasp it easily. This handrail shall not extend over
the vertical projection of the wheelchair space, except by not more than 90mm and only at
a height not less than 850mm above the floor of the wheelchair space;
3.8.4.1.5. A retractable handrail or any equivalent rigid device shall be fitted on the opposite side of
the wheelchair space in order to restrict any lateral shift of the wheelchair and to allow the
wheelchair user to grasp it easily;
3.8.4.1.6. A sign shall be fixed adjacent to the wheelchair area with the following text:
"This space is reserved for a wheelchair. The wheelchair shall be placed facing rearwards
resting against the support or backrest with the brakes on"
The provisions of Paragraph 7.6.11.4. of Annex 3 apply to any textual markings used.
3.8.5. Backrest and Support Requirements
3.8.5.1. A backrest fitted to a wheelchair space in accordance with Paragraph 3.8.4. shall be fitted
perpendicular to the longitudinal axis of the vehicle and shall be capable of bearing a load
of 250 ± 20daN applied to the centre of the padded surface of the backrest, at a height of
not less than 600mm and of not more than 800mm measured vertically from the floor of
the wheelchair space, for a minimum of 1.5s by means of a block 200mm × 200mm in the
horizontal plane of the vehicle towards the front of the vehicle. The backrest shall not
deflect more than 100mm or suffer permanent deformation or damage.
3.8.5.2. A support fitted to a wheelchair space in accordance with Paragraph 3.8.4. shall be fitted
perpendicular to the longitudinal axis of the vehicle and shall be capable of withstanding a
force of 250daN ± 20daN applied to the centre of the support, for a minimum of 1.5s in the
horizontal plane of the vehicle towards the front of the vehicle in the middle of the support.
The support shall not deflect more than 100mm or suffer permanent deformation or
damage.

3.11.1.2. In the event of the failure of a safety device, lifts, ramps and kneeling systems shall be
incapable of operation, unless they can be safely operated by manual effort. The type
and location of the emergency operating mechanism shall be clearly marked. In the
event of power failure, lifts and ramps shall be capable of manual operation.
3.11.1.3. Access to one of the service or emergency doors on the vehicle may be obstructed by a
boarding device providing the following two conditions are satisfied from both inside and
outside the vehicle.
3.11.1.3.1. The boarding device does not obstruct the handle or other device for opening the door.
3.11.1.3.2. The boarding device can be readily moved to leave the doorway clear for use in an
emergency.
3.11.2. Kneeling System
3.11.2.1. A switch shall be required to enable operation of the kneeling system.
3.11.2.2. Any control which initiates the lowering or raising of any part or the whole of the
bodywork relative to the road surface shall be clearly identified and be under the direct
control of the driver.
3.11.2.3. The lowering process shall be capable of being stopped and immediately reversed by a
control both within the reach of the driver, whilst seated in the cab, and also adjacent to
any other operating controls provided for the operation of the kneeling system.
3.11.2.4. Any kneeling system that is fitted to a vehicle shall not allow the vehicle to be driven at a
speed of more than 5km/h when the vehicle is lower than the normal height of travel.
3.11.3. Lift
3.11.3.1. General Provisions
3.11.3.1.1. Lifts shall only be capable of operation when the vehicle is at standstill. Any movement of
the platform shall be prevented unless a device preventing the wheelchair from rolling off
has been activated or has automatically come into operation.
3.11.3.1.2. The lift platform shall not be less than 800mm wide, and not less than 1,200mm long and
shall be capable of operating when carrying a mass of at least 300kg.
3.11.3.2. Additional technical requirements for power-operated lifts
3.11.3.2.1. The operating control shall be designed in such a way that, if released, it automatically
returns to the off position. As it does so the movement of the lift shall immediately be
stopped and it shall be possible to initiate a movement in either direction.
3.11.3.2.2. A safety device (e.g. reversing mechanism) shall protect areas not visible to the
operator, where the movement of the lift might trap or crush objects.
3.11.3.2.3. In the event of one of these safety devices coming into operation, the movement of the
lift shall immediately be stopped and movement in the opposite direction initiated.

3.11.4.3.2. Deployment and stowage of the ramp that may create a risk of injury shall be protected
by a safety device(s).
3.11.4.3.3. These safety devices shall stop the movement of the ramp when the ramp is subject to a
reactive force not exceeding 150N. The peak force may be higher than 150N for a short
time provided that it does not exceed 300N. The reactive force may be measured by any
method to the satisfaction of the Type Approval Authority. Guidelines for measuring the
reactive forces are given in Annex 6 to this Regulation.
3.11.4.3.4. The horizontal movement of a ramp shall be interrupted when a mass of 15kg is placed
upon it.
3.11.4.4. Operation of power-operated ramps
3.11.4.4.1. Where the driver has an adequate view of the ramp sufficient to monitor its deployment
and use, to ensure the safety of passengers, the ramp may be operated by the driver
when in the driver’s seat. This requirement may be met by a suitable indirect vision
device(s).
3.11.4.4.2. In all others cases, the controls shall be adjacent to the ramp. They shall be capable of
being activated and deactivated only by the driver from his seat.
3.11.4.5. Operation of manually-operated ramp
3.11.4.5.1. The ramp shall be so designed that excessive forces are not required to operate the
ramp.

ANNEX 11
MASSES AND DIMENSIONS
1. This Annex applies to the masses and dimensions of vehicles of Categories M and M
in so far as they are necessary for the approval of a vehicle in respect of its general
construction.
2. DEFINITIONS
For the purposes of this Annex:
2.1. "Group of axles" means axles being part of a bogie. A two-axle group is called a
tandem and a tri-axle group a tri-axle bogie. By convention, a solo axle is considered as
a group of one axle.
2.2. "Vehicle dimensions" means the dimensions of the vehicle based on its construction,
as stated by the manufacturer.
2.2.1. "Vehicle length" is a dimension which is measured according to
ISO Standard 612-1978, Term No 6.1.
In addition to the provisions of that Standard, when measuring the vehicle length the
following devices shall not be taken into account:
(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h)
(i)
(j)
(k)
(l)
wiper and washer devices,
front or rear marking-plates,
customs sealing devices and their protection,
devices for securing the tarpaulin and their protection,
lighting equipment,
mirrors and other devices for indirect vision,
watching aids,
air-intake pipes,
length stops for demountable bodies,
access steps and hand-holds,
ram rubbers and similar equipment,
lifting platforms, access ramps and similar equipment in running order, not
exceeding 300mm, provided that the loading capacity of the vehicle is not
increased,

2.3. "Technically permissible maximum mass on the axle (m)" means the mass
corresponding to the maximum permissible static vertical load exerted by the axle on the
road surface, based on the construction of the vehicle and of the axle and as stated by
the vehicle manufacturer.
2.4. "Technically permissible maximum mass on a group of axles (µ)" means the mass
corresponding to the maximum permissible static vertical load exerted by the group of
axles on the road surface, based on both the construction of the vehicle and of the group
of axles and as stated by the vehicle manufacturer.
2.5. "Towable mass" means the total load exerted on the road surface by the axle(s) of the
towed vehicle(s).
2.6. "Technically permissible maximum towable mass (TM)" means the maximum
towable mass stated by the manufacturer.
2.7. "Technically permissible maximum mass on the coupling point of a vehicle"
means the mass corresponding to the maximum permissible static vertical load on the
coupling point based on the construction of the motor vehicle and/or coupling device and
as stated by the manufacturer. By definition, this mass does not include the mass of the
coupling device of the vehicle.
2.8. "Technically permissible maximum laden mass of the combination (MC)" means
the total mass of a combination of vehicle and trailer(s) as stated by the manufacturer.
2.9. "Axle-lift device" means a device permanently fitted to a vehicle for the purpose of
reducing or increasing the load on the axle(s), according to the loading conditions of the
vehicle:
a) either by raising the wheels clear off the ground/lowering them to the ground,
b) or without raising the wheels off the ground, (e.g. in the case of air suspension
systems, or other systems),
in order to reduce the wear on the tyres when the vehicle is not fully laden, and/or make
starting (moving off) on slippery ground easier for vehicles or vehicle combinations, by
increasing the load on the driving axle.
3. REQUIREMENTS
3.1. Measurement of the Mass of the Vehicle in Running Order and of its Distribution
Among the Axles
The mass of the vehicle in running order and its distribution on the axles are measured
on the vehicle(s) submitted in accordance with Paragraph 3.4. of this Regulation placed
in a stationary position with their wheels set straight ahead. If the measured masses
differ by no more than 3% from the masses stated by the manufacturer for the
corresponding technical configurations within the type, or by no more than 5% if the
vehicle is of Category M not exceeding 3,500kg, the masses in running order and their
distribution among the axles as stated by the manufacturer are used for the purpose of
the requirements below. Otherwise the measured masses shall be used and the
technical service may then, if necessary, carry out additional measurements on
vehicle(s) other than those submitted in accordance with Paragraph 3.4. of this
Regulation.

3.2.2.4. MC shall not exceed M + TM.
3.2.3. Loading Conditions
3.2.3.1. The mass of the vehicle in running order, plus the mass Q multiplied by the number of
seated and standing passengers, plus the masses WP, B and BX as defined in
Paragraph 3.2.3.2.1. below, plus the technical permissible maximum mass on the
coupling point, if a coupling is fitted by the manufacturer, shall not exceed the mass M.
3.2.3.2. When the vehicle in running order is laden as described in Paragraph 3.2.3.2.1. below,
the mass corresponding to the load on each axle shall not exceed the mass m on each
axle, and the mass corresponding to the load on each solo axle or group of axles shall
not exceed the mass µ on that group of axles. Moreover, the mass corresponding to the
load on the driving axle or the sum of masses, corresponding to the loads on the driving
axles shall be at least 25% of M.
3.2.3.2.1. The vehicle in running order is loaded with: a mass corresponding to the number P of
seated passengers, of mass Q; a mass corresponding to the number SP of standing
passengers, of mass Q uniformly distributed over the surface available for standing
passengers S ; where appropriate, a mass WP uniformly distributed over each
wheelchair space; a mass equal to B (kg) uniformly distributed in the baggage
compartments; a mass equal to BX (kg) uniformly distributed over the surface area of the
roof equipped for the carriage of baggage, where:
P is the number of seated passengers.
S is the area for standing passengers. In the case of vehicles of Classes III or B, S = 0.
SP, declared by the manufacturer, shall not exceed the value S /S , where S is the
conventional space provided for one standing passenger specified in the table below.
WP (kg), is the number of wheelchair spaces multiplied by 250kg representing the mass
of a wheelchair and user.
B (kg), declared by the manufacturer, shall have a numeric value not less than 100 × V.
This shall include baggage compartments or racks that may be attached to the outside of
the vehicle.
V is the total volume of baggage compartments in m . When approving a vehicle of Class
I or A, the volume of baggage compartments accessible only from the outside of the
vehicle shall be disregarded.
BX, declared by the manufacturer, shall have a numeric value not less than 75kg/m .
Double deck vehicles shall not be equipped for the carriage of baggage on the roof and
therefore BX for double deck vehicles shall be zero.

3.3. Marking of Vehicles
3.3.1. The vehicle shall be clearly marked on the inside in a position visible to the driver in his
seating position:
3.3.1.1. In letters or pictograms not less than 10mm high and numbers not less than 12mm high,
with:
3.3.1.1.1. The maximum number of seating places the vehicle is designed to carry;
3.3.1.1.2. The maximum number of standing places, if any, the vehicle is designed to carry;
3.3.1.1.3. The maximum number of wheelchairs which the vehicle is designed to carry, if any.
3.3.1.2. In letters or pictograms not less than 10mm high and numbers not less than 12mm high,
with:
3.3.1.2.1. The mass of baggage which may be carried when the vehicle is fully loaded according to
Paragraph 3.2.3. of this Annex.
3.3.1.2.2. As appropriate this shall include the mass of baggage:
3.3.1.2.2.1. In baggage compartments (Mass B, Paragraph 3.2.3.2.1. above);
3.3.1.2.2.2. on the roof if equipped for the carriage of baggage (Mass BX, Paragraph 3.2.3.2.1.
above).
3.3.2. Space shall be provided adjacent to the above markings allowing the vehicle to be
marked, in letters or pictograms not less than 10mm high and numbers not less than
12mm high, with the mass of baggage B and BX which may be carried when the vehicle
is loaded with the maximum number of passengers and crew and the vehicle is not
exceeding the maximum laden mass, or the maximum mass of any axle or group of
axles at which the vehicle can be put into service in the Contracting Party where it is to
be registered. Contracting Parties that require the marking of this mass shall, in
agreement with the manufacturer, determine the mass of baggage to be marked and
take the necessary measures to ensure that vehicles are so marked prior to their
registration.
3.4. Manoeuvrability
3.4.1. Any vehicle shall be able to manoeuvre on either side for a complete circular trajectory of
360° inside an area defined by two concentric circles, the outer circle having a radius of
12.50m and the inner circle having a radius of 5.30m, without any of the vehicle's
outermost points (with the exception of the protruding parts excluded from the
measurement of the vehicle width) projecting outside the circumferences of the circles.
For vehicles with axle-lift devices, this requirement also applies with the retractable
axle(s) in the lifted position or loadable axle(s) in the unladen condition.
3.4.1.1. The requirements of Paragraph 3.4.1. above shall be verified with the outermost front
point of the vehicle guided along the contour of the outer circle (see Figure A).

R = 12.5m
r = 5.3m
U = maximum 0.6m
Figure C
3.4.3. The requirements of Paragraphs 3.4.1. and 3.4.2. above may also be verified, at the
request of the manufacturer, with an appropriate equivalent calculation or geometric
demonstration.
3.4.4. In the case of incomplete vehicles, the manufacturer shall declare the maximum
permissible dimensions for which the vehicle is to be checked against the requirements
of Paragraphs 3.4.1. and 3.4.2. above.

2. POWER COLLECTION
2.1. Electrical power shall be obtained from the contact wires by means of one or more power
collection devices, normally comprising two trolley booms. (A single trolley boom or a
pantograph may be used in guided applications). A trolley boom shall consist of a roof
mounting (trolley base), a pole, an electrical power collector (trolley head) and a
replaceable contact surface insert. Trolley booms shall be mounted so that they can turn
in both horizontal and vertical directions.
2.2. Poles shall be made of an insulated material or of metal covered with insulating material
and shall be resistant to mechanical shocks.
2.3. Power collectors shall be designed to maintain adequate positive contact with the
contact wires when the wires are located at between 4 and 6m above the ground and, in
the case of trolley booms, to allow the longitudinal axis of the trolleybus to deviate at
least 4.0m to either side of the mean axis of the contact wires.
2.4. If the power collector becomes accidentally detached from the contact wire (dewired),
the upper end of the power collector(s) shall not be raised higher than 7.2m above the
road, or 1m maximum above the contact wires at the time of de-wiring, nor lower than
0.5m above the roof of the trolleybus.
2.5. Each trolley boom shall be equipped with a device which retracts the boom automatically
if the pole unwires.
2.6. The trolley head, if dismounted from its normal position on the pole, shall be remain
attached to the pole and shall not fall down.
2.7. The insulation resistance between the electric power collector and the roof
mounting/trolley base shall be at least 10МΩ:
2.8. Power collectors may be equipped with remote control from the driver's compartment, at
least for retraction.
2.9. Provision shall be made to enable the driver to replace, if necessary, contact surface
inserts while the vehicle is in operation on the road.
3. TRACTION AND AUXILIARY EQUIPMENT
3.1. Electrical components installed on the trolleybus shall be protected against over-voltage
and short-circuit current. The protection shall preferably be assured by circuit breakers
that are reset automatically, remotely or manually.
3.2. Electrical components shall be protected against commutation or atmospheric
over-voltage.
3.3. Circuit breakers shall provide interruption of particular damaged circuits.
3.4. If any circuit includes a single-pole circuit breaker, it shall be installed in the positive wire
of the circuit.
3.5. All electrical circuits and circuit branches shall be of dual wiring. The trolleybus body can
be used for current earth return only for low voltage circuits.

3.10.12. All electrical circuits shall undergo an excess voltage test. The test voltage shall be
AC with a frequency of 50Hz and approximately sinusoidal form. The time of application
of the test voltage shall be 1min.
3.10.12.1. The test voltage U for electrical equipment and wiring for high voltage circuits shall be:
where U is the rated line voltage
U = 2.5U + 2,000V AC,
3.10.12.2. The test voltage for low voltage circuits shall be U = 750V AC.
3.11. Electrical machines, apparatus, devices and wiring shall withstand mechanical loads,
applied to mounting points, as follows:
3.11.1. Sine-wave form vibration of 0.5 - 55Hz frequency and 10m/s maximum amplitude
including resonance if produced;
3.11.2. Vertical discrete shocks of 30m/s peak shock acceleration lasting 2 - 20ms.
4. ELECTRICAL SAFETY OF PASSENGERS AND CREW
4.1. At the rated climate conditions, with the trolleybus dry and clean and connected to both
positive and negative power supply via the power collection devices, the earth leakage
current from the body shall not be higher than 0.2mA.
4.2. The trolleybus shall be equipped with an onboard device for permanent monitoring of
leakage current or voltage between the chassis and the road surface. The device shall
disconnect the high voltage circuits from the contact system if the leakage current
exceeds 3mA at a line voltage of 600V DC, or if the leakage voltage exceeds 40V.
4.3. Stanchions and handrails at doorways shall be made of insulating material or covered
with mechanically durable insulation or insulated from the trolleybus body. The insulation
resistance shall at least be 1.0MΩ over a contact area of 10,000 ± 500mm .
4.4. The first steps shall be made of insulating material or covered with mechanically durable
insulation. The insulation resistance shall at least be 1.0MΩ over a contact area of
30,000 ± 500mm .
4.5. Door panels shall be made of insulating material or insulated from the trolleybus body.
The insulation resistance shall be at least 1.0MΩ over a contact area on the panel of
30,000 ± 500mm .
4.6. The external body panels adjacent to the door apertures shall be covered with insulating
material. The insulated area shall extend in width at least 500mm each side of the door
apertures and in height at least 2,000mm from the roadway. The insulation resistance in
respect to the trolleybus body shall not be less than 1.0MΩ over a contact area of
20,000 ± 500mm .
4.7. If the trolleybus is equipped with double-insulated converters, Paragraphs 4.3 to 4.6.
above need not be applied.

General Construction of M2 or M3 Vehicles