Regulation No. 86-01 Proposal

Name:Regulation No. 86-01 Proposal
Description:Lighting and Signalling Installation - Agricultural Vehicles. Proposal for the 01 Series.
Official Title:Proposal for the 01 Series of Amendments to Regulation No. 86 (Installation of Lighting and Light-signalling Devices for Agricultural Vehicles).
Country:ECE - United Nations
Date of Issue:2016-08-31
Amendment Level:Original
Number of Pages:18
Information:Published as Regulation No. 86-01
Vehicle Types:Agricultural Tractor
Subject Categories:Drafts and Proposals (Historical)
Available on InterRegs.NET

Our online subscription service, offering immediate access to our extensive library of global vehicle regulations, standards and legislation. A fully searchable, accurate, user-friendly resource for consolidated regulations that are updated quickly and frequently.

Tell me more | Already a subscriber

Available on SelectRegs.com

Our fast and easy means of purchasing up-to-date global vehicle and component standards and regulations on a pay-as-you-go basis. Pay securely by credit card and your documents are delivered directly and immediately to your computer as PDF files.

Tell me more | Go straight to site

Keywords:

vehicles, paragraph, read, lamps, amend, rear, category, regulation, vehicle, lamp, front, signalling, amendments, series, presence, categories, type, visibility, approval, form, mandatory, direction-indicator, white, optional, width, requirements, red, position, horizontal, angle, number, annex, surface, arrangement, height, side, devices, panel, foil, specifications, distance, length, retro-reflector, impossible, prohibited, installation, visible, retro-reflectors, geometric, reduced

Text Extract:

All InterRegs documents are formatted as PDF files and contain the full text, tables, diagrams and illustrations of the original as issued by the national government authority. We do not re-word, summarise, cut or interpret the regulatory documents. They are consolidated, published in English, and updated on a regular basis. The following text extract indicates the scope of the document, but does not represent the actual PDF content.

ECE/TRANS/WP.29/2016/83
PROPOSAL FOR THE 01 SERIES OF AMENDMENTS TO
REGULATION NO. 86
(INSTALLATION OF LIGHTING AND LIGHT-SIGNALLING
DEVICES FOR AGRICULTURAL VEHICLES)
ADOPTED AT THE 170 SESSION – NOVEMBER 2016
PROVISIONAL DATE OF ENTRY INTO FORCE: JUNE 22, 2017

PROPOSAL FOR THE 01 SERIES OF AMENDMENTS TO
REGULATION NO. 86
(INSTALLATION OF LIGHTING AND LIGHT-SIGNALLING
DEVICES FOR AGRICULTURAL VEHICLES)
Paragraph 1., amend to read:
"1. SCOPE
This Regulation applies to vehicles of Category T, R and S, with regard to the installation
of lighting and light-signalling devices."
Paragraph 2.8.2., delete.
Insert a new Paragraph 2.20.3., to read:
"2.20.3. "Signalling panel or signalling foil" means a device used to indicate to other road users
the presence of a wide or long vehicle when viewed from the front, rear or side."
Paragraph 4.2., amend to read:
"4.2. An approval number shall be assigned to each type approved. Its first two digits (at present
01, corresponding to the 01 series of amendments) shall indicate the series of amendments
incorporating the most recent major technical amendments to the Regulation. The same
Contracting Party may not assign the same number to another vehicle type or to the same
vehicle type submitted with equipment not specified in the list referred to in Paragraph 3.2.2.
above subject to Paragraph 7. of this Regulation."
Paragraph 5.1.1., amend to read:
"5.1.1. Vehicles must be fitted with the permanently connected socket outlet specified in
ISO Standard 1724:2003 (Road vehicles – Connectors for the electrical connection of
towing and towed vehicles – 7 pole connector type 12N (normal) for vehicles with 12V
nominal supply voltage), or ISO 1185:2003 (Road vehicles – Connectors for the electrical
connection of towing and towed vehicles – 7-pole connector type 24N (normal) for vehicles
with 24V nominal supply voltage) or both when they have a connection for attaching trailed
vehicles or mounted machines."
Paragraph 5.9.1., amend to read:
"5.9.1. Direction-indicator lamps and the vehicle-hazard warning signal shall be flashing lamps.
Amber side-marker lamps may be flashing lamps."

Paragraph 6.1.1., amend to read:
"6.1.1.
Presence:
Mandatory for vehicles of Category T having a
maximum design speed of more than 40km/h.
Paragraph 6.2.1., amend to read:
Optional on other vehicles of Category T.
Prohibited on vehicles of Categories R and S."
"6.2.1. Presence: Mandatory on vehicles of Category T.
Prohibited on vehicles of Categories R and S."
Paragraph 6.3.1., amend to read:
"6.3.1.
Presence:
Optional on vehicles of Category T. Prohibited
on vehicles of Categories R and S."
Paragraph 6.5.1., amend to read:
"6.5.1. Presence: Mandatory. Types of indicators fall into
Categories (1, 1a, 1b, 2a, 2b, 5 and 6) the
assembly of which on one tractor constitutes
an arrangement (A to D).
Arrangement A and D shall be allowed only on
vehicles of Category T whose overall length
does not exceed 4,600mm and in the case of
which the distance between the outer edges of
the illuminating surfaces is not more than
1.60m.
Arrangements B and C shall apply to all
vehicles of Category T.
For vehicles of Categories R and S
Category 2a lamps shall be used.
Additional direction-indicator lamps optional."

6.5.3.2. For vehicles of Categories R and S: Two rear direction-indicator lamps
(Category 2a) with angles of geometric visibility
according to Arrangement B, C or D."
Paragraph 6.5.4.3., amend to read:
"6.5.4.3.
Length:
The distance between the center of reference
of illuminating surface of the Category 1
indicator (Arrangement "B"), Category 5 or 6
indicator (Arrangement "B" and "C") and the
transverse plane which marks the forward
boundary
of
the
tractor's
overall
length
normally shall not exceed 1,800mm. If the
structure of the tractor makes it impossible to
keep to the minimum angles of visibility, this
distance may be increased to 2,600mm."
Paragraph 6.7.5., amend to read:
"6.7.5.
Geometric visibility:
Horizontal angle: 45° outwards and inwards.
The horizontal inward angle may be reduced to
30° if the shape of the bodywork makes it
impossible to reach 45°.
Paragraph 6.8.1., amend to read:
Vertical angle: 15° above and below the
horizontal.
The vertical angle below the horizontal may be
reduced to 10° or 5° where the lamp has its
H Plane at or below 1,900mm respectively
950mm from the ground."
"6.8.1. Presence: Mandatory on all vehicles of Category T.
Mandatory on all vehicles of Categories R and
S exceeding 1,600mm in width.
Optional on other vehicles of Categories R
and S.
The front position lamps may be omitted if
end-outline marker lamps are installed and
meet all the installation requirements for front
position lamps."

Paragraph 6.14.1., amend to read:
"6.14.1. Presence: Mandatory on vehicles of Category T.
Prohibited on vehicles of Categories R and S."
Paragraph 6.14.2., amend to read:
"6.14.2. Number: Two or four (see Paragraph 6.14.5.1.).
Paragraph 6.15.1., amend to read:
The performances of these devices shall
conform to the requirements concerning
Class IA or IB retro-reflectors in Regulation
No. 3. Additional retro-reflecting devices and
materials (including two retro-reflectors not
complying with Paragraph 6.14.4. below), are
permitted provided they do not impair the
effectiveness of the mandatory lighting and
light-signalling devices."
"6.15.1.
Presence:
Mandatory on vehicles of Category T the
length of which exceeds 6m and on all vehicles
of Categories R and S.
Paragraph 6.15.4.3., amend to read:
Optional on tractors the length of which does
not exceed 6m."
"6.15.4.3.
Length:
One reflector must be not more than 3m from
the foremost point of the vehicle, and either the
same reflector or a second reflector must be
not more than 3m from the rearmost point of
the vehicle. For vehicles of Category R and S
the distance between the rearmost side
retro-reflector and the rear of the vehicle shall
not exceed 1m.
Paragraph 6.17.1., amend to read:
The distance between two reflectors on the
same side of the vehicle must not exceed 3m.
If the structure, design or the operational use of
the vehicle makes it impossible to comply with
such a requirement, this distance may be
increased to 4m."
"6.17.1.
Presence:
Optional on vehicles of Category T. Mandatory
on vehicles of Categories R and S."

Insert a new Paragraph 6.25., to read:
"6.25. Rear Retro-reflectors, Triangular (Regulation No. 3)
6.25.1.
Presence:
Mandatory on vehicles of Categories R and S.
Prohibited on vehicles of Category T.
6.25.2. Number: Two or four (see Paragraph 6.25.5.1.).
6.25.3.
Arrangement:
The apex of the triangle shall be directed
upwards.
6.25.4. Position
6.25.4.1.
Width:
Except as provided in Paragraph 6.25.5.1. the
point on the illuminating surface which is
farthest from the vehicle's median longitudinal
plane shall be not more than 400mm from the
extreme outer edge of the vehicle. The inner
edges of the retro-reflectors shall be not less
than 600mm apart. This distance may be
reduced to 400mm where the overall width of
the vehicle is less than 1,300mm.
6.25.4.2.
Height:
Except as provided in Paragraph 6.25.5.1., not
less than 400mm and not more than 1,500mm
above the ground.
For vehicles with a maximum width not
exceeding 1,300mm above the ground not less
than 250mm.
6.25.4.3. Length: No individual specifications.
6.25.5. Geometric visibility: Horizontal angle: 30° inwards and outwards.
Vertical angle: 15° above and below the
horizontal. The vertical angle below the
horizontal may be reduced to 5° if the height of
the reflector is less than 750mm.
6.25.5.1. If it is impossible to observe the above position
and visibility requirements, four retro-reflectors
may be fitted in accordance with the following
installation specifications:

Insert a new Paragraph 12., to read:
"12. TRANSITIONAL PROVISIONS
12.1. As from the official date of entry into force of the 01 series of amendments, no Contracting
Party applying this Regulation shall refuse to grant or refuse to accept type approvals under
this Regulation as amended by the 01 series of amendments.
12.2. As from 24 months after the date of entry into force of the 01 series of amendments,
Contracting Parties applying this Regulation shall grant type approvals only if the vehicle
type to be approved meets the requirements of this Regulation as amended by the 01 series
of amendments.
12.3. Contracting Parties applying this Regulation shall not refuse to grant extensions of type
approvals for existing types which have been granted according to the preceding series of
amendments to this Regulation.
12.4. Until 24 months after the date of entry into force of the 01 series of amendments to this
Regulation, no Contracting Party applying this Regulation shall refuse national or regional
type approval of a vehicle type-approved to the preceding series of amendments to this
Regulation.
12.5. As from 24 months after the date of entry into force of the 01 series of amendments to this
Regulation, Contracting Parties applying this Regulation shall not be obliged to accept, for
the purpose of national or regional type approval, a vehicle type approved to the preceding
series of amendments to this Regulation.
12.6. Notwithstanding the transitional provisions above, Contracting Parties whose application of
this Regulation comes into force after the date of entry into force of the 01 series of
amendments are only obliged to accept type approval granted in accordance with the
01 series of amendments."
Item 5.16., amend to read:
ANNEX 1,
"5.16. Rear retro-reflectors, non-triangular: yes/no .............................................................................. "
Item 5.21., amend to read:
"5.21. Daytime running lamps: yes/no .................................................................................................. "
Item 5.22., amend to read:
"5.22. Cornering lamps: yes/no ............................................................................................................ "
Insert new Items 5.26. to 5.28., to read:
"5.26. Exterior courtesy lamps: yes/no ................................................................................... "
"5.27. Signalling panels or signalling foils: yes/no ................................................................................ "
"5.28. Rear retro-reflectors, triangular: yes/no ..................................................................................... "

Annex 5, amend to read:
"ANNEX 5
DIRECTION-INDICATOR LAMPS - GEOMETRIC VISIBILITY
(see Paragraph 6.5.54.)

Insert a new Annex 6, to read:
"ANNEX 6
SIGNALLING PANELS AND SIGNALLING FOILS
1. DIMENSIONS, ARRANGEMENT, NUMBER AND MINIMUM REFLECTING SURFACE
1.1. Signalling Panels and Signalling Foils shall have the following Dimensions:
Dimensions in mm
Figure 1
Basic Standard Area
Dimensions in mm
Figure 2
Signalling Panel or Signalling Foil

Lighting and Signalling Installation - Agricultural Vehicles. Proposal for the 01 Series.