Regulation No. 119-01 Proposed Supplement 5
|Name:||Regulation No. 119-01 Proposed Supplement 5|
|Description:||Cornering Lamps. Proposed Supplement 5 to the 01 Series.|
|Official Title:||Proposal for Supplement 5 to the 01 Series of Amendments to Regulation No. 119 (Cornering Lamps).|
|Country:||ECE - United Nations|
|Date of Issue:||2016-12-20|
|Number of Pages:||6|
|Vehicle Types:||Agricultural Tractor, Bus, Car, Component, Heavy Truck, Light Truck|
|Subject Categories:||Drafts and Proposals (Historical)|
Available on InterRegs.NET
Our online subscription service, offering immediate access to our extensive library of global vehicle regulations, standards and legislation. A fully searchable, accurate, user-friendly resource for consolidated regulations that are updated quickly and frequently.
Tell me more | Already a subscriber
Available on SelectRegs.com
Our fast and easy means of purchasing up-to-date global vehicle and component standards and regulations on a pay-as-you-go basis. Pay securely by credit card and your documents are delivered directly and immediately to your computer as PDF files.
Tell me more | Go straight to site
lamp, light, paragraph, source, lamps, read, case, filament, type, non-replaceable, approval, amend, requirements, manufacturer, cornering, samples, sample, mark, module, regulation, voltage, deviation, documentation, failure, insert, trade, conformity, specimen, annex, gear, control, iec, equipped, marked, colour, sampling, edition, electronic, single, production, intensity, compliance, produced, vehicle, tell-tale, indicating, renumber, paragraphs, identification, part
All InterRegs documents are formatted as PDF files and contain the full text, tables, diagrams and illustrations of the original as issued by the national government authority. We do not re-word, summarise, cut or interpret the regulatory documents. They are consolidated, published in English, and updated on a regular basis. The following text extract indicates the scope of the document, but does not represent the actual PDF content.
PROPOSAL FOR SUPPLEMENT 5 TO THE 01 SERIES OF
REGULATION NO. 119
ADOPTED AT THE 171 SESSION – MARCH 2017
PROVISIONAL DATE OF ENTRY INTO FORCE: OCTOBER 10, 2017
Paragraph 5., amend to read:
"5. General Specifications
The requirements contained in Sections 5. "General Specifications" and 6. "Individual
Specifications" and in the Annexes referenced in the said sections of Regulations Nos. 48 or
86, and their series of amendments in force at the time of application for the lamp type
approval shall apply to this Regulation.
The requirements pertinent to each lamp and to the category/ies of vehicle on which the
lamp is intended to be installed shall be applied, where its verification at the moment of lamp
type approval is feasible.
Insert a new paragraph 5.5., to read:
"5.5. In the case of non-replaceable filament lamp(s) or light source module(s) equipped with
non-replaceable filament lamp(s), the applicant shall annex to the type approval
documentation a report (by the light source manufacturer indicated in the type approval
documentation), acceptable to the Authority responsible for type approval, that
demonstrates compliance of these non-replaceable filament lamp(s) with the requirements
as specified in Paragraph 4.11. of IEC 60809, Edition 3."
Paragraph 6.4., amend to read:
"6.4. In the case of a single lamp containing more than one light source when all light sources are
illuminated the maximum intensities shall not be exceeded."
Insert a new Paragraph 6.5., to read:
"6.5. Failure of a Single Lamp Containing more than One Light Source:
6.5.1. In a single lamp containing more than one light source, a group of light sources, wired so
that the failure of any one of them causes all of them to stop emitting light, shall be
considered to be one light source.
6.5.2. In case of failure of any one light source in a single lamp containing more than one light
source, at least one of the following provisions shall apply:
The light intensity complies with the minimum intensity required in the table of
standard light distribution in space as shown in Annex 3, or
(b) A signal for activation of a tell-tale indicating failure, as indicated in Paragraph 6.20.8.
of Regulation No. 48, is produced, provided that the luminous intensity at 2.5°D 45°L
for a left-side lamp (the L angle should be substituted for the R angle for a right-side
lamp) is at least 50% of the minimum intensity required. In this case a note in the
communication form states that the lamp is only for use on a vehicle fitted with a
tell-tale indicating failure."
Paragragh 7.5., shall be deleted.
Insert new Paragraphs 1.4. to 1.4.2., to read:
"1.4. In the case of non-replaceable filament lamp(s) or light source module(s) equipped with
non-replaceable filament lamps, at any conformity of production check:
1.4.1. The holder of the approval mark shall demonstrate the use in normal production and show
the identification of the non-replaceable filament lamp(s) as indicated in the type approval
1.4.2. In the case where doubt exists in respect to compliance of the non-replaceable filament
lamp(s) with lifetime requirements and/or, in the case of colour coated filament lamps, with
colour endurance requirements, as specified in Paragraph 4.11 of IEC 60809, Edition 3,
conformity shall be checked (by the light source manufacturer indicated in the type approval
documentation) as specified in Paragraph 4.11. of IEC 60809, Edition 3."
Paragraphs 2. to 5., amend to read:
"2. First Sampling
In the first sampling four cornering lamps are selected at random. The first sample of two is
marked A, the second sample of two is marked B.
2.1. The conformity of mass-produced cornering lamps shall not be contested if the deviation of
any specimen of samples A and B (all four lamps) is not more than 20%.
In the case, that the deviation of both lamps of sample A is not more than 0%, the
measurement can be closed.
2.2. The conformity of mass-produced cornering lamps shall be contested if the deviation of at
least one specimen of samples A or B is more than 20%.
The manufacturer shall be requested to bring his production in line with the requirements
(alignment) and a repeated sampling according to Paragraph 3. below shall be carried out
within two months' time after the notification. The samples A and B shall be retained by the
Technical Service until the entire Conformity of Production process is finished.
3. First Repeated Sampling
A sample of four lamps is selected at random from stock manufactured after alignment.
The first sample of two is marked C, the second sample of two is marked D.
3.1. The conformity of mass-produced cornering lamps shall not be contested if the deviation of
any specimen of samples C and D (all four lamps) is not more than 20%.
In the case, that the deviation of both lamps of sample C is not more than 0% the
measurement can be closed.