Regulation No. 7-02 Proposed Supplement 26
|Name:||Regulation No. 7-02 Proposed Supplement 26|
|Description:||Position, Stop and End-outline Lamps. Proposed Supplement 26 to the 02 Series.|
|Official Title:||Proposal for Supplement 26 to the 02 Series of Amendments to Regulation No. 7 (Position, Stop and End-outline Lamps).|
|Country:||ECE - United Nations|
|Date of Issue:||2016-12-19|
|Number of Pages:||8|
|Vehicle Types:||Agricultural Tractor, Bus, Car, Component, Heavy Truck, Light Truck, Trailer|
|Subject Categories:||Drafts and Proposals (Historical)|
Available on InterRegs.NET
Our online subscription service, offering immediate access to our extensive library of global vehicle regulations, standards and legislation. A fully searchable, accurate, user-friendly resource for consolidated regulations that are updated quickly and frequently.
Tell me more | Already a subscriber
Available on SelectRegs.com
Our fast and easy means of purchasing up-to-date global vehicle and component standards and regulations on a pay-as-you-go basis. Pay securely by credit card and your documents are delivered directly and immediately to your computer as PDF files.
Tell me more | Go straight to site
paragraph, lamps, lamp, light, read, type, source, case, filament, regulation, non-replaceable, amend, requirements, intensity, approval, sample, mark, minimum, position, front, conformity, marked, trade, documentation, manufacturer, annex, end-outline, single, insert, equipped, module, failure, rear, maximum, contested, values, edition, approved, voltage, compliance, iec, variable, random, marker, colour, respect, photometric, mass-produced, set, required
All InterRegs documents are formatted as PDF files and contain the full text, tables, diagrams and illustrations of the original as issued by the national government authority. We do not re-word, summarise, cut or interpret the regulatory documents. They are consolidated, published in English, and updated on a regular basis. The following text extract indicates the scope of the document, but does not represent the actual PDF content.
PROPOSAL FOR SUPPLEMENT 26 TO THE 02 SERIES OF
REGULATION NO. 7
(POSITION, STOP AND END-OUTLINE LAMPS)
ADOPTED AT THE 171 SESSION – MARCH 2017
PROVISIONAL DATE OF ENTRY INTO FORCE: OCTOBER 10, 2017
Paragraph 3.6.3., amend to read:
"3.6.3. The marking of the rated voltage or range of voltage."
Paragraph 5., amend to read:
"5. General Specifications
The requirements contained in Sections 5. "General Specifications" and 6. "Individual
Specifications" and in the Annexes referenced in the said sections of Regulations Nos. 48,
53, 74 or 86, and their series of amendments in force at the time of application for the lamp
type approval shall apply to this Regulation.
The requirements pertinent to each lamp and to the category/ies of vehicle on which the
lamp is intended to be installed shall be applied, where its verification at the moment of lamp
type approval is feasible.
Insert a new Paragraph 5.11., to read:
"5.11. In the case of non-replaceable filament lamp(s) or light source module(s) equipped with
non-replaceable filament lamp(s), the applicant shall annex to the type approval
documentation a report (by the light source manufacturer indicated in the type approval
documentation), acceptable to the Authority responsible for type approval, that
demonstrates compliance of these non-replaceable filament lamp(s) with the requirements
as specified in Paragraph 4.11. of IEC 60809, Edition 3."
220.127.116.11. In case of failure of any one light source in a single lamp containing more than one light
source, at least one of the following provisions shall apply:
The light intensity complies with the minimum intensity required in the table of
standard light distribution in space as shown in Annex 4, or
(b) A signal for activation of a tell-tale indicating failure, as indicated in Paragraphs 6.7.8.,
6.9.8, 6.10.8. and 6.13.8. of Regulation No. 48, is produced, provided that the
luminous intensity in the axis of reference is at least 50% of the minimum intensity
required. In this case a note in the communication form states that the lamp is only for
use on a vehicle fitted with a tell-tale indicating failure."
Paragraph 9.1., amend to read:
"9.1. Lamps shall be so manufactured as to conform to the type approved under this Regulation.
The compliance with the requirements set forth in Paragraphs 6. and 8. above shall be
verified as follows: … "
Paragraph 9.2. (former), renumber as Paragraph 9.1.1.
Paragraph 9.3. (former), renumber as Paragraph 9.1.2.
Paragraph 9.4. (former), renumber as Paragraph 9.2.
Insert a new Paragraph 9.3, to read:
"9.3. In the case of non-replaceable filament lamp(s) or light source module(s) equipped with
non-replaceable filament lamps, a report (by the light source manufacturer indicated in the
type approval documentation) shall demonstrate compliance of these non-replaceable
filament lamp(s) with lifetime requirements and, in the case of colour coated filament lamps,
also with colour endurance requirements, as specified in Paragraph 4.11. of IEC 60809,
Paragraphs 1.2. to 1.3., amend to read:
"1.2. With respect to photometric performances, the conformity of mass-produced lamps shall not
be contested if, when testing according to Paragraph 7. of this Regulation, the photometric
performances as set forth in Paragraph 6. of this Regulation of any lamp chosen at random:
1.2.1. No measured value deviates unfavourably by more than 20% from the values prescribed in
Paragraph 2. to 5., amend to read:
"2. First Sampling
In the first sampling four lamps are selected at random. The first sample of two is marked A,
the second sample of two is marked B.
2.1. The conformity of mass-produced lamps shall not be contested if the deviation of any
specimen of samples A and B (all four lamps) is not more than 20%.
In the case, that the deviation of both lamps of sample A is not more than 0% the
measurement can be closed.
2.2. The conformity of mass-produced lamps shall be contested if the deviation of at least one
specimen of samples A or B is more than 20%.
The manufacturer shall be requested to bring his production in line with the requirements
(alignment) and a repeated sampling according to Paragraph 3. below shall be carried out
within two months' time after the notification. The samples A and B shall be retained by the
Technical Service until the entire Conformity of Production process is finished.
3. First Repeated Sampling
A sample of four lamps is selected at random from stock manufactured after alignment.
The first sample of two is marked C, the second sample of two is marked D.
3.1. The conformity of mass-produced lamps shall not be contested if the deviation of any
specimen of samples C and D (all four lamps) is not more than 20%.
In the case, that the deviation of both lamps of sample C is not more than 0%, the
measurement can be closed.
3.2. The conformity of mass-produced lamps shall be contested if the deviation of at least:
3.2.1. One specimen of samples C or D is more than 20% but the deviation of all specimen of
these samples is not more than 30%.
The manufacturer shall be requested again to bring his production in line with the
A second repeated sampling according to Paragraph 4. below shall be carried out within two
months' time after the notification. The samples C and D shall be retained by the Technical
Service until the entire Conformity of Production process is finished.
3.2.2. One specimen of samples C or D is more than 30%.
In this case the approval shall be withdrawn and Paragraph 5. below shall be applied.